Campbell Scientific CSAT3 CSAT3 3-D Sonic Anemometer - Page 20

CRBasic Dataloggers, 1.2 EDLOG Dataloggers, 1.3 CR9000

Get Campbell Scientific CSAT3 PDF manuals and user guides View all Campbell Scientific CSAT3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

CSAT3 Three Dimensional Sonic Anemometer TABLE 6-2. SDM Compatible Dataloggers Datalogger Model 21X 1K 21X 2K CR10 2K CR10 4K CR10X CR23X CR9000 CR5000 CR9000X CR1000 CR3000 CR800/850 Datalogger PROMs or Operating System (OS) 6145-3, 6146-5, 10006-1 6148-5, 6149-7, 6070-64 5954-396 Library Special OS 1.4 or > All OS 2.01 or > All OS All OS All OS All OS All OS Requires CSAT3 embedded code 2.1 or > 2.1 or > 2.1 or > 2.1 or > 2.1 or > 2.1 or > 2.1 or > 3.0 or > 3.0 or > 3.0 or > 3.0 or > 3.0 or > 6.1.1 CRBasic Dataloggers SDM is a Campbell Scientific communication protocol used between a Campbell Scientific datalogger and a smart sensor. This protocol uses SDM dedicated control ports (CR3000, CR5000, and CR9000X) or multipurpose control ports (CR1000, CR800/850) to communicate with the CSAT3. SDM protocol allows synchronized measurement and rapid communication between a datalogger and the CSAT3. The CRBasic datalogger instruction, CSAT3 () is used to communicate with the CSAT3 over the SDM bus. 6.1.2 EDLOG Dataloggers SDM is a Campbell Scientific communication protocol used between a Campbell Scientific dataloggers and a smart sensor. This protocol uses SDM dedicated control ports (CR23X) or multipurpose control ports (21X or CR10(X)) to communicate with the CSAT3. With a 21X, single ended analog input channel 1 (labeled 1H) and a 10 K resistor is used in conjunction with control port 1. SDM protocol allows synchronized measurement and rapid communication between a datalogger and the CSAT3. The EDLOG datalogger instruction, SDM-CSAT3 (P107), is used to communicate with the CSAT3 over the SDM bus. 6.1.3 CR9000 SDM communications between the CR9000 and CSAT3 is achieved via the 9 pin CSI serial I/O port on the 9080 peripheral and memory card. The CR9000 instruction CSAT3() is used to communicate with the CR9000 over the SDM bus. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
CSAT3 Three Dimensional Sonic Anemometer
TABLE 6-2.
SDM Compatible Dataloggers
Datalogger
Model
Datalogger PROMs or
Operating System (OS)
Requires CSAT3
embedded code
21X 1K
6145-3, 6146-5, 10006-1
2.1 or >
21X 2K
6148-5, 6149-7, 6070-64
2.1 or >
CR10 2K
5954-396
2.1 or >
CR10 4K
Library Special
2.1 or >
CR10X
OS 1.4 or >
2.1 or >
CR23X
All OS
2.1 or >
CR9000
2.01 or >
2.1 or >
CR5000
All OS
3.0 or >
CR9000X
All OS
3.0 or >
CR1000
All OS
3.0 or >
CR3000
All OS
3.0 or >
CR800/850
All OS
3.0 or >
6.1.1 CRBasic Dataloggers
SDM is a Campbell Scientific communication protocol used between a
Campbell Scientific datalogger and a smart sensor.
This protocol uses SDM
dedicated control ports (CR3000, CR5000, and CR9000X) or multipurpose
control ports (CR1000, CR800/850) to communicate with the CSAT3.
SDM
protocol allows synchronized measurement and rapid communication between
a datalogger and the CSAT3.
The CRBasic datalogger instruction, CSAT3 () is
used to communicate with the CSAT3 over the SDM bus.
6.1.2 EDLOG Dataloggers
SDM is a Campbell Scientific communication protocol used between a
Campbell Scientific dataloggers and a smart sensor.
This protocol uses SDM
dedicated control ports (CR23X) or multipurpose control ports (21X or
CR10(X)) to communicate with the CSAT3.
With a 21X, single ended analog
input channel 1 (labeled 1H) and a 10 K resistor is used in conjunction with
control port 1.
SDM protocol allows synchronized measurement and rapid
communication between a datalogger and the CSAT3.
The EDLOG datalogger
instruction, SDM-CSAT3 (P107), is used to communicate with the CSAT3
over the SDM bus.
6.1.3 CR9000
SDM communications between the CR9000 and CSAT3 is achieved via the 9
pin CSI serial I/O port on the 9080 peripheral and memory card.
The CR9000
instruction CSAT3() is used to communicate with the CR9000 over the SDM
bus.
12