Cisco WRV200 User Guide

Cisco WRV200 - Small Business Wireless-G VPN Router Manual

Get Cisco WRV200 - Small Business Wireless-G VPN Router PDF manuals and user guides
UPC - 745883570577
View all Cisco WRV200 manuals
Add to My Manuals
Save this manual to your list of manuals

Cisco WRV200 manual content summary:

  • Cisco WRV200 | User Guide - Page 1
    USER GUIDE Wireless-G VPN Router with RangeBooster Model: WRV200 BUSINESS SERIES v
  • Cisco WRV200 | User Guide - Page 2
    in the U.S. and certain other countries. Copyright © 2007 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders. Wireless-G VPN Router with RangeBooster Open Source This product may contain material licensed to
  • Cisco WRV200 | User Guide - Page 3
    What is a VPN 3 VPN Router to VPN Router 4 Computer (using the Linksys VPN client software) to VPN Router 4 Chapter 4: Product Overview 5 Front Panel 5 Back Panel 5 Chapter 5: Configuring the Wireless-G VPN Router 6 Overview 6 How to Access the Web-based Utility 7 Setup 7 Setup > Basic
  • Cisco WRV200 | User Guide - Page 4
    28 Administration > Factory Default 28 Administration > Firmware Upgrade 28 Administration > Reboot 29 Status 29 Status > Router 29 Status > Local Network 30 Status > Wireless 30 Status > System Performance 30 Status > VPN Clients 31 Appendix A: Troubleshooting 32 Frequently Asked
  • Cisco WRV200 | User Guide - Page 5
    62 Wireless Disclaimer 62 Avis de non-responsabilité concernant les appareils sans fil 62 User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE 63 Appendix J: Contact Information 67 Wireless-G VPN Router with RangeBooster
  • Cisco WRV200 | User Guide - Page 6
    Chapter 1 Chapter 1: Introduction Thank you for choosing the Wireless-G VPN Router with RangeBooster. The WRV200 is a VPN router with a Wireless-G access point for small offices and home offices. The 10/100 Ethernet WAN interface connects directly to your broadband DSL or Cable modem. For the LAN
  • Cisco WRV200 | User Guide - Page 7
    network computers, the wireless network should be set up in Infrastructure mode. The basis of Infrastructure mode centers around an access point or wireless router, such as the Wireless-G VPN Router, which serves as the main point of communications in a wireless network. The Router transmits data to
  • Cisco WRV200 | User Guide - Page 8
    a VPN connection: • VPN Router to VPN Router • Computer (using the Linksys VPN client software) to VPN Router IMPORTANT: You must have at least one VPN Router on one end of the VPN tunnel. At the other end of the VPN tunnel, you must have a second VPN Router or a computer with the Linksys VPN client
  • Cisco WRV200 | User Guide - Page 9
    dials up her ISP. Her notebook computer has the Linksys VPN client software, which is configured with her office's IP address. She accesses the Linksys VPN client software and connects to the VPN Router at the central office. As VPNs utilize the Internet, distance is not a factor. Using the
  • Cisco WRV200 | User Guide - Page 10
    factory defaults from the Administration > Factory Defaults screen of the Router's Web-based Utility. INTERNET The Internet port connects to your cable or DSL modem. 1-4 (ETHERNET) The four Ethernet ports connect to your PCs and other network devices. Wireless-G VPN Router with RangeBooster 
  • Cisco WRV200 | User Guide - Page 11
    . Click the Administration tab and then the Management tab. The Router's default password is admin. To secure the Router, change the Password from its default. There are seven main tabs: Setup, Wireless, Firewall, VPN, QoS, Administration, and Status. Additional tabs will be available after
  • Cisco WRV200 | User Guide - Page 12
    general settings. Address Bar of Web Browser NOTE: The default IP address is 192.168.1.1. If the IP address has been changed using DHCP, enter the assigned IP address instead of the default. Password Request Wireless-G VPN Router with RangeBooster Setup > Basic Settings - Automatic Configuration
  • Cisco WRV200 | User Guide - Page 13
    to-Point Protocol over Ethernet) to establish Internet connections. If you are connected to the Internet through a DSL line, check with your ISP to see if they use PPPoE. If they do, you will have to enable PPPoE. Wireless-G VPN Router with RangeBooster PPPoE User Name and Password/Confirm Password
  • Cisco WRV200 | User Guide - Page 14
    Your ISP will provide you with the Default Gateway Address. L2TP Server IP Enter the IP address of the L2TP server. User Name and Password Enter the User Name and Password provided by your ISP. Connect on Demand: Max Idle Time You can configure the Router to cut the Internet connection after it
  • Cisco WRV200 | User Guide - Page 15
    IP Table Time Settings This is where you set the time for the Router. You can set the time and date manually or automatically. Manually Select the date from the Date drop-down menus. Then enter the time in the Time fields. Wireless-G VPN Router with RangeBooster Automatically Select your time
  • Cisco WRV200 | User Guide - Page 16
    . Setup > DDNS - TZO Email, TZO Password Key, and Domain Name Enter the Email Address, TZO Password Key, and Domain Name of the service you set up with TZO. Internet IP Address The Router's current Internet IP Address is displayed here. Because it is dynamic, this will change. Wireless-G VPN
  • Cisco WRV200 | User Guide - Page 17
    route from the drop-down menu. The Router supports up to 5 static route entries. Wireless-G VPN Router with RangeBooster Delete This Entry If you need to IP address, Subnet Mask, Gateway, and Interface are displayed. Click Refresh to update the information. Click Close to exit this screen. Setup
  • Cisco WRV200 | User Guide - Page 18
    the default setting, Enable. If you do not want to broadcast the Router's SSID, then select Disabled. WMM WMM (Wi-Fi Multimedia) is a component of the IEEE 802.11e wireless LAN standard for quality of service (QoS). Wireless-G VPN Router with RangeBooster It specifically supports priority tagging
  • Cisco WRV200 | User Guide - Page 19
    .) Enter the RADIUS Wireless-G VPN Router with RangeBooster Wireless Security - WPA2 Enterprise This option features WPA2 used in coordination with a RADIUS server. (This should only be used when a RADIUS server is connected to the Router.) Enter the RADIUS server's IP address. Enter the RADIUS
  • Cisco WRV200 | User Guide - Page 20
    undo your changes. For help information, click More. WPA2 Enterprise Mixed Wireless Security - WPA2 Enterprise Mixed Wireless-G VPN Router with RangeBooster Wireless Security - RADIUS To indicate which WEP key to use, select the appropriate Default Transmit Key number. Then, select the level of WEP
  • Cisco WRV200 | User Guide - Page 21
    Default Wireless-G VPN Router with RangeBooster Changes to undo your changes. For help information, click More. Wireless > Wireless Network Access This screen allows you to control access to your wireless network for each SSID. Wireless > Wireless Network Access Wireless Network Access Access
  • Cisco WRV200 | User Guide - Page 22
    Mode's default setting is Auto.The Router will automatically use CTS Protection Mode when your Wireless-G products are experiencing severe problems and are not able to transmit to the Router in an environment with heavy 802.11b traffic. This function boosts the Router's ability Wireless-G VPN Router
  • Cisco WRV200 | User Guide - Page 23
    . This mode allows a wireless client to connect to the Router through a repeater, such as WAP54GP or WAP54GPE, when operating in the Repeater Mode. This mode allows you to extend the coverage of the Router by using up to three repeaters. Select Auto Select to enable the remote access point when
  • Cisco WRV200 | User Guide - Page 24
    Chapter 5 Configuring the Wireless-G Router The Port Forwarding screen sets up public services on your network, such as web servers, ftp servers, e-mail servers, or other specialized Internet applications. (Specialized Internet applications are any applications that use Internet access to perform
  • Cisco WRV200 | User Guide - Page 25
    more secure. VPN > VPN Client Access The Router offers a QuickVPN Client utility for Windows 2000 or XP. If the Router has clients using this utility, then you can designate the QuickVPN clients and their passwords on the VPN > VPN Client Access screen. Wireless-G VPN Router with RangeBooster 20
  • Cisco WRV200 | User Guide - Page 26
    the Wireless-G Router VPN > VPN Client Access User Name Enter a name for the VPN client. Password Enter a password for the VPN client. Re-enter to confirm Enter the password again to confirm it. Allow user to change password? If you want to let the user change his or her password from the user
  • Cisco WRV200 | User Guide - Page 27
    Chapter 5 Configuring the Wireless-G Router PPTP PassThrough Point-to-Point Tunneling Protocol (PPTP) allows the Point-to-Point Protocol (PPP) to be tunneled through an IP network. PPTP Passthrough is enabled by default. To disable it, select Disabled. L2TP PassThrough Layer 2 Tunneling Protocol
  • Cisco WRV200 | User Guide - Page 28
    mode to Main (default) or Aggressive. Main Mode operation is supported in ISAKMP SA establishment. ISAKMP Encryption Method There are four different types of encryption: 3DES, AES-128, AES-192, or AES256. You may choose any of these, but it must be the Wireless-G VPN Router with RangeBooster
  • Cisco WRV200 | User Guide - Page 29
    . Specify the number of times IKE must fail before the Router blocks that unauthorized IP address. Anti-replay This protects the Router from anti-replay attacks, when people try to capture your authentication packets in an attempt to gain access. The feature is enabled by default. When you have
  • Cisco WRV200 | User Guide - Page 30
    bandwidth for other applications. User Define Button You can define the policies regarding source or destination IP, protocol and port number. select High Priority or Low Priority. The packets will be Wireless-G VPN Router with RangeBooster QoS > Port-Based QoS Priority Select the QoS priority
  • Cisco WRV200 | User Guide - Page 31
    Play) features. Wireless-G VPN Router with RangeBooster Admin Password To ensure the Router's security, you will be asked for your password when you access the Router's Web-based Utility. The default user name and password is admin. Admin Password You should change the default password to one of
  • Cisco WRV200 | User Guide - Page 32
    and follow the on-screen instructions. Restore Configurations To restore the Router's configuration, click this button and follow the on-screen instructions. (You must have previously backed up the Router's configuration.) Wireless-G VPN Router with RangeBooster When you have finished making
  • Cisco WRV200 | User Guide - Page 33
    stop the test, Wireless-G VPN Router with RangeBooster Administration > Firmware Upgrade The Administration > Firmware Upgrade screen allows you to upgrade the Router's firmware. Do not upgrade the firmware unless you are experiencing problems with the Router or the new firmware has a feature you
  • Cisco WRV200 | User Guide - Page 34
    selected on the Setup Tab. Wireless-G VPN Router with RangeBooster Status > Router Information Hardware Version This shows the installed version and date of the hardware. Software Version This shows the installed version and date of the software. Current Time The current time is displayed here
  • Cisco WRV200 | User Guide - Page 35
    , MAC Addresses, and length of time until a computer's assigned IP address expires. Click Close to return to the Local Network screen. Click Refresh to update the information. Status > Wireless Mode As selected from the Wireless tab, this will display the wireless mode (Mixed, G-Only, or Disabled
  • Cisco WRV200 | User Guide - Page 36
    received is displayed here. Packets Sent The number of packets sent is displayed here. Wireless-G VPN Router with RangeBooster Status > VPN Clients VPN Summary VPN Client Users Display Select the group of VPN client users whose information you wish to see. No. This is the number assigned to the
  • Cisco WRV200 | User Guide - Page 37
    A: Troubleshooting This appendix provides solutions to problems that may occur during the installation and operation of the Router. Read the descriptions below to help solve your problems. If you can't find an answer here, check the Linksys website at www.linksys.com. I need to set a static IP
  • Cisco WRV200 | User Guide - Page 38
    or the dial-up pop-up window (for PPPoE users)" below. I can't get my Virtual Private Network (VPN) to work through the Router. Access the Router's web interface by going to http://192.168.1.1 or the IP address of the Router, and go to the VPN -> VPN Pass Through tab. Make sure you have IPSec
  • Cisco WRV200 | User Guide - Page 39
    Appendix A Troubleshooting number used in the VPN IP address), the Router will have difficulties routing information to the right location. If you change the Router's IP address to 192.168.2.1, that should solve the problem. Change the Router's IP address through the Setup tab of the Web-based
  • Cisco WRV200 | User Guide - Page 40
    the Reset button for ten seconds and then releasing it. If you are still getting prompted for a password when saving settings, then perform the following steps: 1. Access the Router's web interface by going to http://192.168.1.1 or the IP address of the Router. Enter the default password admin, and
  • Cisco WRV200 | User Guide - Page 41
    steps: 1. To connect to the Router, go to the web browser, and enter http://192.168.1.1 or the IP address of the Router. 2. Enter the password, if asked (the default password is admin). 3. Go to the Setup -> Basic Setup tab. 4. Look for the MTU option, and select Manual. In the MTU Size field, enter
  • Cisco WRV200 | User Guide - Page 42
    other than Windows 2000 or Windows XP? Yes, but Linksys does not, at this time, provide technical support for setup, configuration or troubleshooting of any non-Windows operating systems. Wireless-G VPN Router with RangeBooster Does the Router support ICQ send file? Yes, with the following fix
  • Cisco WRV200 | User Guide - Page 43
    can I be notified of new Router firmware upgrades? All Linksys firmware upgrades are posted on the Linksys website at www.linksys.com, where they can be downloaded for free. The Router's firmware can be upgraded using the Web-based Utility. If the Router's Internet connection is working well, there
  • Cisco WRV200 | User Guide - Page 44
    networks. 2. Change the default password For wireless products such as access points, routers, and gateways, you will be asked for a password when you want to change their settings. These devices have a default password set by the factory. The Linksys default password is admin. Hackers know these
  • Cisco WRV200 | User Guide - Page 45
    QuickVPN only works with a Linksys Wireless‑G VPN Router with RangeBooster that is properly configured to accept a QuickVPN connection. Follow these instructions to configure the Router's VPN client settings: 1. Open the Web-based utility. 2. Click VPN > VPN Client Access. Go to the Start menu
  • Cisco WRV200 | User Guide - Page 46
    the User Name and Password fields, enter the User Name and Password that were assigned to you. In the Server Address field, enter the IP address or domain name of the Linksys Wireless-G VPN Router with RangeBooster. In the Port For QuickVPN field, enter the port number that the QuickVPN client will
  • Cisco WRV200 | User Guide - Page 47
    QuickVPN Client and specify the User Name, Password, and Server Address (IP address or domain name). c. Click Connect. For more information on certificate management, go to section "VPN > VPN Client Access" in "Chapter 5: Configuring the Wireless-G Router." Wireless-G VPN Router with RangeBooster
  • Cisco WRV200 | User Guide - Page 48
    an example. Subnet Mask: 255.255.255.0 WRV200 WAN IP Address: 140.111.1.1
  • Cisco WRV200 | User Guide - Page 49
    list, and de-select the Use Add Wizard check box. Click Add. Filters Properties In the Source address field, select My IP Address. In the Destination address field, select A specific IP Subnet, and enter the IP Address 192.168.1.0 and Subnet Wireless-G VPN Router with RangeBooster IP Filter List
  • Cisco WRV200 | User Guide - Page 50
    Configure Individual Tunnel Rules Tunnel 1: win->Router 1. On the IP Filter List tab, select filter list win->Router. Security Methods Tab 4. Select the Authentication Methods tab, and click Edit. IP Filter List Tab Wireless-G VPN Router with RangeBooster Authentication Methods Tab 5. Change the
  • Cisco WRV200 | User Guide - Page 51
    8. Select the Connection Type tab, and click All network connections. Then, click the OK or Close button to finish this rule. Wireless-G VPN Router with RangeBooster IP Filter List Tab 11. Click the Filter Action tab, and select the filter action Require Security. Then, click Edit. On the Security
  • Cisco WRV200 | User Guide - Page 52
    The tunnel endpoint is specified by this IP Address, and enter the Windows 2000/XP computer's IP Address. Authentication Methods Tab 13. Change appears on your screen; otherwise, proceed to the next step. Wireless-G VPN Router with RangeBooster Connection Type Tab 17. On the Rules tab, click the
  • Cisco WRV200 | User Guide - Page 53
    default user name and password, admin. Press Enter. 3. Click the VPN tab, then click IPSec VPN. VPN > IPSec VPN 4. Select the tunnel you wish to create in the Select Tunnel Entry drop-down box. Then click Enabled next to the VPN Tunnel option. Enter the name of the tunnel in Wireless-G VPN Router
  • Cisco WRV200 | User Guide - Page 54
    the WRV200 Follow these instructions for the first VPN Router, designated WRV200. The other VPN Router is designated the RV082. 1. Launch the web browser for a networked computer, designated PC 1. 2. Access the web-based utility of the WRV200. (Refer to "Chapter 5: Configuring the Wireless-G Router
  • Cisco WRV200 | User Guide - Page 55
    . 10. In the IPSec Setup section, select the appropriate encryption, authentication, and other key management settings. (These should match the settings of the WRV200.) 11. In the Preshared Key field, enter a string for this key, for example, test1234. Wireless-G VPN Router with RangeBooster 50
  • Cisco WRV200 | User Guide - Page 56
    the WRV200 Follow these instructions for the first VPN Router, designated WRV200. The other VPN Router is designated the RV082. 1. Launch the web browser for a networked computer, designated PC 1. 2. Access the web-based utility of the WRV200. (Refer to "Chapter 5: Configuring the Wireless-G Router
  • Cisco WRV200 | User Guide - Page 57
    the WRV200 Follow these instructions for the first VPN Router, designated WRV200. The other VPN Router is designated the RV082. 1. Launch the web browser for a networked computer, designated PC 1. 2. Access the web-based utility of the WRV200. (Refer to "Chapter 5: Configuring the Wireless-G Router
  • Cisco WRV200 | User Guide - Page 58
    ." Configuration of the RV082 Follow similar instructions for the RV082. 1. Launch the web browser for a networked computer, designated PC 2. 2. Access the Web-based Utility of the RV082. (Refer to the User Guide of the RV082 for details.) 3. Click the IPSec VPN tab. 4. Click the Gateway to Gateway
  • Cisco WRV200 | User Guide - Page 59
    single line, but only one direction at a time. HTTP (HyperText Transport Protocol) The communications protocol used to connect to servers on the World Wide Web. Infrastructure A wireless network that is bridged to a wired network via an access point. IP (Internet Protocol) A protocol used to send
  • Cisco WRV200 | User Guide - Page 60
    ability to take a wireless device from one access point's range to another without losing the connection. Wireless-G VPN Router with RangeBooster Router A networking device that connects multiple networks together. Server Any computer whose function in a network is to provide user access to files
  • Cisco WRV200 | User Guide - Page 61
    and associated devices that communicate with each other wirelessly. WPA (Wi-Fi Protected Access) A wireless security protocol using TKIP (Temporal Key Integrity Protocol) encryption, which can be used in conjunction with a RADIUS server. Glossary Wireless-G VPN Router with RangeBooster 56
  • Cisco WRV200 | User Guide - Page 62
    (3DES) Setup/Config User Interface Built-in Web UI for easy browser-based configuration (HTTP/HTTPS) Management SNMP Version SNMP version 1, 2c Event Logging Local, Syslog, E-mail Firmware Upgrade Firmware Upgradable Through Web Browser Diagnostics Flash, RAM, LAN, WLAN Wireless Spec
  • Cisco WRV200 | User Guide - Page 63
    kg) 12V 1A FCC Class B, CE, IC 32 to 104ºF (0 to 40ºC) -4 to 158ºF (-20 to 70ºC) 10 to 85% Noncondensing 5 to 90% Noncondensing Specifications Wireless-G VPN Router with RangeBooster 58
  • Cisco WRV200 | User Guide - Page 64
    (VAR) from whom you purchased the product or Linksys Technical Support for instructions on how to obtain warranty service. The telephone number for Linksys Technical Support in your area can be found in the product User Guide and at www.linksys.com. Have your product serial number and proof of
  • Cisco WRV200 | User Guide - Page 65
    for support services) can be found at: www.linksys.com/support. This limited warranty is governed by the laws of the jurisdiction in which the Product was purchased by you. Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine, CA 92623. Warranty Information Wireless-G VPN Router
  • Cisco WRV200 | User Guide - Page 66
    used according to the instructions, may cause harmful interference turning the equipment off and on, the user is encouraged to try to correct the 802.11g operation of this product in the USA is firmware-limited to channels 1 through 11. Safety Notices • Wireless-G VPN Router with RangeBooster 61
  • Cisco WRV200 | User Guide - Page 67
    au point d'accès, du volume du trafic réseau, des matériaux utilisés dans le bâtiment et du type de construction, du système d'exploitation et de la combinaison de produits sans fil utilisés, des interférences et de toute autre condition défavorable. Wireless-G VPN Router with RangeBooster 62
  • Cisco WRV200 | User Guide - Page 68
    users with regards to the proper disposal and recycling of Linksys products. Consumers are required to comply with this notice for all electronic products bearing the following symbol: English - Environmental Information for Customers eller de lokale Wireless-G VPN Router with RangeBooster 63
  • Cisco WRV200 | User Guide - Page 69
    pārstrāde tiek veikta pareizi, tad mazinās iespējamais kaitējums dabai un cilvēku veselībai. Sīkākas ziņas par novecojuša aprīkojuma izmešanu atkritumos jūs varat saņemt vietējā pašvaldībā, atkritumu savākšanas dienestā, kā arī veikalā, kur iegādājāties šo izstrādājumu. Wireless-G VPN Router with
  • Cisco WRV200 | User Guide - Page 70
    a terméket vásárolta. Nederlands (Dutch) - Milieu-informatie voor klanten in de Europese Unie De Europese Richtlijn 2002/96/EC schrijft voor dat apparatuur die is voorzien van dit , służb oczyszczania miasta lub sklepu, w którym produkt został nabyty. Wireless-G VPN Router with RangeBooster 65
  • Cisco WRV200 | User Guide - Page 71
    - Informação ambiental para clientes da União Europeia A Directiva vechi, contactaţi autorităţile locale, serviciul de salubrizare sau magazinul de la care aţi achiziţionat produsul. Slovenčina WEB: For additional information, please visit www.linksys.com Wireless-G VPN Router with RangeBooster
  • Cisco WRV200 | User Guide - Page 72
    Line 800-546-5797 (LINKSYS) Support 800-326-7114 RMA (Return Merchandise Authorization) http://www.linksys.com/warranty NOTE: Details on warranty and RMA issues can be found in the Warranty section of this Guide. Contact Information Wireless-G VPN Router with RangeBooster 7111510A-AI 67
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
USER GUIDE
BUSINESS SERIES
Wireless-G VPN Router
with RangeBooster
Model:
WRV200