Compaq 8000 Technical Reference Guide: HP Compaq 8000 Elite Series Business De - Page 80

Power Management, 4.2 Wake Up Events

Get Compaq 8000 - Elite Convertible Minitower PC PDF manuals and user guides
UPC - 884420665106
View all Compaq 8000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

Power and Signal Distribution 7.4.2 Wake Up Events The system can be activated with a power "wake-up" of the system due to the occurrence of a magic packet, serial port ring, or PCI power management event (PME). These events can be individually enabled through the Setup utility to wake up the system from a sleep (low power) state. ✎ Wake-up functionality requires that certain circuits receive auxiliary power while the system is turned off. The system unit must be plugged into a live AC outlet for wake up events to function. Using an AC power strip to control system unit power will disable wake-up event functionality. The wake up sequence for each event occurs as follows: Wake-On-LAN The network interface controller (NIC) can be configured for detection of a "Magic Packet" and wake the system up from sleep mode through the assertion of the PME- signal on the PCI bus. Refer to Chapter 5, "Network Support" for more information. Modem Ring A ring condition on a serial port can be detected by the power control logic and, if so configured, cause the power control logic to wake up the system. Power Management Event A power management event that asserts the PME- signal on the PCI bus can be enabled to cause the power control logic to wake up the system. Note that the PCI card must be PCI ver. 2.2 (or later) compliant to support this function. 7.5 Power Management These systems include power management functions that conserve energy by turning off or inhibiting power to various subsystems and components. These functions are provided by a combination of hardware, firmware (BIOS) and software. These systems provide the following power management support: ■ ACPI v2.0 compliant (ACPI modes C1, S1, and S3-S5) ■ APM 1.2 compliant ■ U.S. EPA Energy Star 3.0 and 4.0 compliant Table 7-6 shows the comparison in power states. 7-6 www.hp.com Technical Reference Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
7-6
www.hp.com
Technical Reference Guide
Power and Signal Distribution
7.4.2 Wake Up Events
The system can be activated with a power “wake-up” of the system due to the occurrence of a
magic packet, serial port ring, or PCI power management event (PME). These events can be
individually enabled through the Setup utility to wake up the system from a sleep (low power)
state.
✎
Wake-up functionality requires that certain circuits receive auxiliary power while the system is
turned off.
The system unit must be plugged into a live AC outlet for wake up events to function.
Using an AC power strip to control system unit power will disable wake-up event functionality.
The wake up sequence for each event occurs as follows:
Wake-On-LAN
The network interface controller (NIC) can be configured for detection of a “Magic Packet” and
wake the system up from sleep mode through the assertion of the PME- signal on the PCI bus.
Refer to Chapter 5, “Network Support” for more information.
Modem Ring
A ring condition on a serial port can be detected by the power control logic and, if so configured,
cause the power control logic to wake up the system.
Power Management Event
A power management event that asserts the PME- signal on the PCI bus can be enabled to cause
the power control logic to wake up the system. Note that the PCI card must be PCI ver. 2.2 (or
later) compliant to support this function.
7.5 Power Management
These systems include power management functions that conserve energy by turning off or
inhibiting power to various subsystems and components. These functions are provided by a
combination of hardware, firmware (BIOS) and software. These systems provide the following
power management support:
■
ACPI v2.0 compliant (ACPI modes C1, S1, and S3-S5)
■
APM 1.2 compliant
■
U.S. EPA Energy Star 3.0 and 4.0 compliant
Table 7-6 shows the comparison in power states.