Compaq BL20p Installation Guide - Page 22

Installing the Access Panel, Memory, Identifying DIMM Slots

Get Compaq BL20p - HP ProLiant - 512 MB RAM PDF manuals and user guides
UPC - 720591771058
View all Compaq BL20p manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

Installing the Server Blade and Options Installing the Access Panel After installing all the options, reinstall the access panel: 1. Set the access panel on top of the server blade. Allow the panel to extend past the rear of the server blade approximately 1 cm (3/8 inch). 2. Slide the access panel forward until it fits into place (1). 3. Tighten the thumbscrew on the rear of the server blade (2). Figure 2-5: Installing the access panel Memory You can expand system memory by installing Compaq synchronous DRAM (SDRAM) DIMMs. A ProLiant BL20p server blade supports up to four 1-GB, 133-MHz, ECC, registered SDRAM DIMMs. Identifying DIMM Slots Use Figure 2-6 and Table 2-2 to identify DIMM slot locations. The slots are numbered sequentially (1 through 4), and the paired banks are identified by the letters A and B. 2-8 Compaq ProLiant BL20p Server Blade Setup and Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Installing the Server Blade and Options
2-8
Compaq ProLiant BL20p Server Blade Setup and Installation Guide
Installing the Access Panel
After installing all the options, reinstall the access panel:
1.
Set the access panel on top of the server blade. Allow the panel to extend past the
rear of the server blade approximately 1 cm (3/8 inch).
2.
Slide the access panel forward until it fits into place (1).
3.
Tighten the thumbscrew on the rear of the server blade (2).
Figure 2-5:
Installing the access panel
Memory
You can expand system memory by installing Compaq synchronous DRAM
(SDRAM) DIMMs. A ProLiant BL20p server blade supports up to four 1-GB,
133-MHz, ECC, registered SDRAM DIMMs.
Identifying DIMM Slots
Use Figure 2-6 and Table 2-2 to identify DIMM slot locations. The slots are
numbered sequentially (1 through 4), and the paired banks are identified by the letters
A and B.