Compaq BL20p Installation Guide - Page 74

Panel in Appendix E, LEDs and Switches., Compaq Integrated Lights-Out User Guide - enclosure management module

Get Compaq BL20p - HP ProLiant - 512 MB RAM PDF manuals and user guides
UPC - 720591771058
View all Compaq BL20p manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

Troubleshooting If the server blade does not start: 1. Be sure that the server blade is fully seated in the enclosure. 2. Be sure that power is applied to the blade: a. Check the status using the system power LED. For the location and explanation of the system power LED, refer to the "Server Blade Front Panel" section in Appendix E, "LEDs and Switches." b. Check the server blade management modules and power management modules for proper cabling and power configuration switch settings. c. The server blade is configured to power up upon insertion. However, if you changed that setting, be sure that the Power On/Standby button was pressed firmly. 3. If the system does not complete POST or start loading an operating system: a. Use the iLO remote console or the iLO system status page to identify POST messages. Refer to the Compaq Integrated Lights-Out User Guide. b. Refer to the section on loose connections in the Compaq Servers Troubleshooting Guide. 4. Ensure the server blade is not rebooting repeatedly: a. Be sure that the system is not rebooting due to a problem that initiates an ASR-2 reboot. ASR-2 is defaulted to restart the server blade automatically, loading the operating system. If a critical error occurs, ASR-2 logs the error in the IML and restarts the server blade. For more information, refer to the Compaq Servers Troubleshooting Guide. b. Use the iLO remote console to identify a possible thermal event. 5. Restart the server blade. If the server blade does not restart, proceed to the "Server Blade Diagnostic Steps" section in this appendix. D-2 Compaq ProLiant BL20p Server Blade Setup and Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Troubleshooting
D-2
Compaq ProLiant BL20p Server Blade Setup and Installation Guide
If the server blade does not start:
1.
Be sure that the server blade is fully seated in the enclosure.
2.
Be sure that power is applied to the blade:
a.
Check the status using the system power LED. For the location and
explanation of the system power LED, refer to the “Server Blade Front
Panel” section in Appendix E, “LEDs and Switches.”
b.
Check the server blade management modules and power management
modules for proper cabling and power configuration switch settings.
c.
The server blade is configured to power up upon insertion. However, if you
changed that setting, be sure that the Power On/Standby button was pressed
firmly.
3.
If the system does not complete POST or start loading an operating system:
a.
Use the iLO remote console or the iLO system status page to identify POST
messages. Refer to the
Compaq Integrated Lights-Out User Guide
.
b.
Refer to the section on loose connections in the
Compaq Servers
Troubleshooting Guide
.
4.
Ensure the server blade is not rebooting repeatedly:
a.
Be sure that the system is not rebooting due to a problem that initiates an
ASR-2 reboot.
ASR-2 is defaulted to restart the server blade automatically, loading the
operating system. If a critical error occurs, ASR-2 logs the error in the IML
and restarts the server blade.
For more information, refer to the
Compaq Servers Troubleshooting Guide
.
b.
Use the iLO remote console to identify a possible thermal event.
5.
Restart the server blade. If the server blade does not restart, proceed to the
“Server Blade Diagnostic Steps” section in this appendix.