D-Link DGS-3630-28TC Hardware Installation Guide - Page 37

COM Port Configuration, Set flow control to none.

Get D-Link DGS-3630-28TC PDF manuals and user guides View all D-Link DGS-3630-28TC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

DGS-3630 Series Layer 3 Stackable Managed Switch Hardware Installation Guide  Connect the male DB9 connector on the console cable (shipped with the Switch) to the RS-232 serial port on the computer running terminal emulation software then insert the RJ45 connector into the RJ45 console port on the front of the Switch. To configure the terminal emulation software as follows:  Select the appropriate serial port (COM1 or COM2).  Set the data rate to 115200 baud.  Set the data format to 8 data bits, 1 stop bit, and no parity.  Set flow control to none. Figure 5-1 COM Port Configuration To be able to view the boot procedure, the Switch needs to be rebooted. The simplest way, at this stage, to reboot the Switch is to unplug and re-insert the power cable from and into the power receptacle on the back of the Switch. After correctly configuring the terminal settings and re-inserting the power cable, the boot procedure will appear in the terminal. Boot Procedure V1.00.006 Power On Self Test 100 % MAC Address : F0-7D-68-36-30-00 H/W Version : A1 Please Wait, Loading 1.00.018 Runtime Image UART init Starting runtime image Device Discovery Configuration init 100 % 100 % 100 % 100 % After the boot sequence has been completed, the console login screen will be displayed. 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
DGS-3630 Series Layer 3 Stackable Managed Switch Hardware Installation Guide
37
Connect the male DB9 connector on the console cable (shipped with the Switch) to the RS-232 serial port on
the computer running terminal emulation software then insert the RJ45 connector into the RJ45 console port
on the front of the Switch.
To configure the terminal emulation software as follows:
Select the appropriate serial port (COM1 or COM2).
Set the data rate to 115200 baud.
Set the data format to 8 data bits, 1 stop bit, and no parity.
Set flow control to none.
Figure 5-1 COM Port Configuration
To be able to view the boot procedure, the Switch needs to be rebooted. The simplest way, at this stage, to reboot the
Switch is to unplug and re-insert the power cable from and into the power receptacle on the back of the Switch.
After correctly configuring the terminal settings and re-inserting the power cable, the boot procedure will appear in the
terminal.
Boot Procedure
V1.00.006
-------------------------------------------------------------------------------
Power On Self Test
........................................
100 %
MAC Address
: F0-7D-68-36-30-00
H/W Version
: A1
Please Wait, Loading 1.00.018 Runtime Image
...............
100 %
UART init
.................................................
100 %
Starting runtime image
Device Discovery
..........................................
100 %
Configuration init
........................................
100 %
After the boot sequence has been completed, the console login screen will be displayed.