D-Link DGS-3630-28TC Hardware Installation Guide - Page 39

COM Port Configuration

Get D-Link DGS-3630-28TC PDF manuals and user guides View all D-Link DGS-3630-28TC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

DGS-3630 Series Layer 3 Stackable Managed Switch Hardware Installation Guide Set the terminal emulation software as follows:  Select the serial port that belongs to the virtual COM port.  Set the data rate to 115200 baud.  Set the data format to 8 data bits, 1 stop bit, and no parity.  Set flow control to none. Figure 5-4 COM Port Configuration To be able to view the boot procedure, the Switch needs to be rebooted. The simplest way, at this stage, to reboot the Switch is to unplug and re-insert the power cable from and into the power receptacle on the back of the Switch. After correctly configuring the terminal settings and re-inserting the power cable, the boot procedure will appear in the terminal. Boot Procedure V1.00.006 Power On Self Test 100 % MAC Address : F0-7D-68-36-30-00 H/W Version : A1 Please Wait, Loading 1.00.011 Runtime Image UART init Starting runtime image Device Discovery Configuration init 100 % 100 % 100 % 100 % After the boot sequence has been completed, the console login screen will be displayed. 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
DGS-3630 Series Layer 3 Stackable Managed Switch Hardware Installation Guide
39
Set the terminal emulation software as follows:
Select the serial port that belongs to the virtual COM port.
Set the data rate to 115200 baud.
Set the data format to 8 data bits, 1 stop bit, and no parity.
Set flow control to none.
Figure 5-4 COM Port Configuration
To be able to view the boot procedure, the Switch needs to be rebooted. The simplest way, at this stage, to reboot the
Switch is to unplug and re-insert the power cable from and into the power receptacle on the back of the Switch.
After correctly configuring the terminal settings and re-inserting the power cable, the boot procedure will appear in the
terminal.
Boot Procedure
V1.00.006
-------------------------------------------------------------------------------
Power On Self Test
........................................
100 %
MAC Address
: F0-7D-68-36-30-00
H/W Version
: A1
Please Wait, Loading 1.00.011 Runtime Image
...............
100 %
UART init
.................................................
100 %
Starting runtime image
Device Discovery
..........................................
100 %
Configuration init
........................................
100 %
After the boot sequence has been completed, the console login screen will be displayed.