Dell C9000 Line Cards Networking C9010 Getting Started Guide - Page 45

Setting RJ-45 Console Access, RJ-45 Cable and Adapter Pin Assignments

Get Dell C9000 Line Cards PDF manuals and user guides View all Dell C9000 Line Cards manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Figure 33. Console Ports on a Route Processor Module 1. USB-B console port 2. RJ-45 console port Setting RJ-45 Console Access The RJ-45 console port is an asynchronous serial port. If you connect a console to this port, it must support asynchronous transmission. NOTE: Before connecting a console, be sure that a terminal emulation program is already installed on your PC console. 1. Install an RJ-45 copper cable into the console port. To connect the C9010 console port to a terminal server, use the DB-9 to RJ-45 serial console cable shipped with the C9010. 2. Connect the other end of the cable to the DTE terminal server. 3. Set your terminal or terminal emulation mode to VT100 with the following settings: • 9600 baud rate • No parity • 8 data bits • 1 stop bit • Window Terminal Emulator option set to NO • 24 lines x 80 characters • No flow control RJ-45 Cable and Adapter Pin Assignments To configure and monitor your system, you can connect to a terminal port, PC serial port, or a terminal server by using the RJ-45 console port on the RPM. An RJ-45 Ethernet cable is required to connect to the console port. The following table describes the pinouts for the RJ-45 console port. Table 7. Pin Assignments for the RJ-45 Console Port Pin Serial Input/Output 1 NC (unused) - 2 DTR Output 3 TxD Output 4 GND - Configuring the Software 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
Figure 33. Console Ports on a Route Processor Module
1.
USB-B console port
2.
RJ-45 console port
Setting RJ-45 Console Access
The RJ-45 console port is an asynchronous serial port. If you connect a console to this port, it must
support asynchronous transmission.
NOTE:
Before connecting a console, be sure that a terminal emulation program is already installed
on your PC console.
1.
Install an RJ-45 copper cable into the console port. To connect the C9010 console port to a
terminal server, use the DB-9 to RJ-45 serial console cable shipped with the C9010.
2.
Connect the other end of the cable to the DTE terminal server.
3.
Set your terminal or terminal emulation mode to VT100 with the following settings:
•
9600 baud rate
•
No parity
•
8 data bits
•
1 stop bit
•
Window Terminal Emulator option set to NO
•
24 lines x 80 characters
•
No flow control
RJ-45 Cable and Adapter Pin Assignments
To configure and monitor your system, you can connect to a terminal port, PC serial port, or a terminal
server by using the RJ-45 console port on the RPM. An RJ-45 Ethernet cable is required to connect to
the console port.
The following table describes the pinouts for the RJ-45 console port.
Table 7. Pin Assignments for the RJ-45 Console Port
Pin
Serial
Input/Output
1
NC (unused)
-
2
DTR
Output
3
TxD
Output
4
GND
-
Configuring the Software
45