Dell C9000 Line Cards Networking C9010 Getting Started Guide - Page 6

Before You Start: Site Preparation, C9000-RPM-2.56T, 07KPC3, 0N90RW, C9000-FAN, 0C94MF, C9000-PWR-AC

Get Dell C9000 Line Cards PDF manuals and user guides View all Dell C9000 Line Cards manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

The base C9010 configuration package consists of: • One C9010 chassis • One full-width C9000 Series RPM - C9000-RPM-2.56T displays in SW output. - 07KPC3 or 0N90RW is on the HW label. • Three C9000 Series fan modules - C9000-FAN displays in SW output. - 0C94MF is on the HW label. • One AC PSU (110-230V switching) - C9000-PWR-AC displays in SW output. - D3000E-S0 is on the HW label. • AC power cord (IEC 60320 C19 cable) • One DB-9 to RJ-45 serial console cable • One rack bar with four screws and washers • Eight cage nuts (four for the rack bar; four for the chassis thumb screws) • Blank panels: one RPM, three PSU, and nine half-width line card blanks • Two cable management brackets • C9010 Getting Started Guide • Safety and Regulatory Information • Warranty and Support Information • Software License Agreement In addition, you can order the following items: • Up to three additional PSUs for redundancy or additional power • Half-width line cards: - 6-Port 40 Gigabit Ethernet QSFP+ (C9000LC0640 displays in SW output.) - 24-Port 1/10 Gigabit Ethernet SFP+ (C9000LC2410G displays in SW output.) - 24-Port 1/10 Gigabit Ethernet Base-T RJ-45 (C9000LC2410T displays in SW output.) • SFP+ optics • QSFP+ optics • SFP+ direct attach copper (DAC) cables • QSFP+ DAC cables • DB-9 adapter • Dell ReadyRails™ kit (#1 and #2 Phillips and flat-tipped screwdrivers required) with four cage nuts • Rack mount tray • C1048P port extenders for use with the C9010 Before You Start: Site Preparation Before installing the C9010 switch, make sure that your installation site meets these requirements: • Clearance: Ensure there is adequate space in front of the switch so you can read the light-emitting diodes (LEDs) and adequate space around and behind the chassis for cabling, power connections, 6 C9010 Hardware Description

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
The base C9010 configuration package consists of:
•
One C9010 chassis
•
One full-width C9000 Series RPM
–
C9000-RPM-2.56T
displays in SW output.
–
07KPC3
or
0N90RW
is on the HW label.
•
Three C9000 Series fan modules
–
C9000-FAN
displays in SW output.
–
0C94MF
is on the HW label.
•
One AC PSU (110-230V switching)
–
C9000-PWR-AC
displays in SW output.
–
D3000E-S0
is on the HW label.
•
AC power cord (IEC 60320 C19 cable)
•
One DB-9 to RJ-45 serial console cable
•
One rack bar with four screws and washers
•
Eight cage nuts (four for the rack bar; four for the chassis thumb screws)
•
Blank panels: one RPM, three PSU, and nine half-width line card blanks
•
Two cable management brackets
•
C9010 Getting Started Guide
•
Safety and Regulatory Information
•
Warranty and Support Information
•
Software License Agreement
In addition, you can order the following items:
•
Up to three additional PSUs for redundancy or additional power
•
Half-width line cards:
–
6-Port 40 Gigabit Ethernet QSFP+ (
C9000LC0640
displays in SW output.)
–
24-Port 1/10 Gigabit Ethernet SFP+ (
C9000LC2410G
displays in SW output.)
–
24-Port 1/10 Gigabit Ethernet Base-T RJ-45 (
C9000LC2410T
displays in SW output.)
•
SFP+ optics
•
QSFP+ optics
•
SFP+ direct attach copper (DAC) cables
•
QSFP+ DAC cables
•
DB-9 adapter
•
Dell ReadyRails™ kit (#1 and #2 Phillips and flat-tipped screwdrivers required) with four cage nuts
•
Rack mount tray
•
C1048P port extenders for use with the C9010
Before You Start: Site Preparation
Before installing the C9010 switch, make sure that your installation site meets these requirements:
•
Clearance
: Ensure there is adequate space in front of the switch so you can read the light-emitting
diodes (LEDs) and adequate space around and behind the chassis for cabling, power connections,
6
C9010 Hardware Description