Dell Inspiron N5010 Service Manual - Page 26

I/O Board

Get Dell Inspiron N5010 PDF manuals and user guides View all Dell Inspiron N5010 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Back to Contents Page I/O Board Dell™ Inspiron™ N5010/M5010 Service Manual Removing the I/O Board Replacing the I/O Board WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is not covered by your warranty. CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on your computer). CAUTION: To help prevent damage to the system board, remove the main battery (see Removing the Battery) before working inside the computer. Removing the I/O Board 1. Follow the instructions in Before You Begin. 2. Remove the battery (see Removing the Battery). 3. Follow the instructions from step 3 to step 13 in Removing the System Board. 4. Remove the middle cover (see Removing the Middle Cover). 5. Remove the I/O board from the latch on the computer base. 6. Lift the I/O board off the computer base. 1 I/O board Replacing the I/O Board 1. Follow the instructions in Before You Begin. 2. Align the connectors on the I/O board with the slots on the computer base and press the I/O board until it is seated fully. 3. Replace the middle cover (see Replacing the Middle Cover). 4. Follow the instructions from step 6 to step 17 in Replacing the System Board. 5. Replace the battery (see Replacing the Battery). CAUTION: Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may result in damage to the computer.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
Back to Contents Page
I/O Board
Dell™ Inspiron™ N5010/M5010 Service Manual
Removing the I/O Board
Replacing the I/O Board
Removing the I/O Board
1.
Follow the instructions in
Before You Begin
.
2.
Remove the battery (see
Removing the Battery
).
3.
Follow the instructions from
step 3
to
step 13
in
Removing the System Board
.
4.
Remove the middle cover (see
Removing the Middle Cover
).
5.
Remove the I/O board from the latch on the computer base.
6.
Lift the I/O board off the computer base.
Replacing the I/O Board
1.
Follow the instructions in
Before You Begin
.
2.
Align the connectors on the I/O board with the slots on the computer base and press the I/O board until it is seated fully.
3.
Replace the middle cover (see
Replacing the Middle Cover
).
4.
Follow the instructions from
step 6
to
step 17
in
Replacing the System Board
.
5.
Replace the battery (see
Replacing the Battery
).
WARNING:
Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
CAUTION:
Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™
is not covered by your warranty.
CAUTION:
To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal
surface (such as a connector on your computer).
CAUTION:
To help prevent damage to the system board, remove the main battery (see
Removing the Battery
) before working inside the
computer.
1
I/O board
CAUTION:
Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may
result in damage to the computer.