Dell Latitude 7230 Rugged Extreme Tablet Service Manual - Page 45

RJ45-port assembly, Removing the RJ45-port assembly

Get Dell Latitude 7230 Rugged Extreme Tablet PDF manuals and user guides View all Dell Latitude 7230 Rugged Extreme Tablet manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

RJ45-port assembly Removing the RJ45-port assembly Prerequisites 1. Follow the procedure in before working inside your tablet. 2. Remove the stylus. 3. Remove the handle (for the models shipped with a handle). 4. Remove the batteries. 5. Remove the back-cover assembly. About this task The figure indicates the location of the RJ45-port assembly and provides a visual representation of the removal procedure. Steps NOTE: For models shipped with an RJ45 connector in the expansion bay at the top side of the tablet. 1. Open the latch and disconnect the RJ45 FPC from the connector on the RJ45 daughter-board. 2. Remove the four screws (M2x5) that secure the RJ45-port cover to the RJ45-port assembly. 3. Remove the RJ45-port cover from the tablet. 4. Remove the two screws (M2x3) that secure the RJ45-port bezel to the tablet. 5. Remove the RJ45-port assembly away from the tablet. Installing the RJ45-port assembly Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. Removing and installing components 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
RJ45-port assembly
Removing the RJ45-port assembly
Prerequisites
1.
Follow the procedure in
before working inside your tablet
.
2.
Remove the
stylus
.
3.
Remove the
handle
(for the models shipped with a handle).
4.
Remove the
batteries
.
5.
Remove the
back-cover assembly
.
About this task
The figure indicates the location of the RJ45-port assembly and provides a visual representation of the removal procedure.
Steps
NOTE:
For models shipped with an RJ45 connector in the expansion bay at the top side of the tablet.
1.
Open the latch and disconnect the RJ45 FPC from the connector on the RJ45 daughter-board.
2.
Remove the four screws (M2x5) that secure the RJ45-port cover to the RJ45-port assembly.
3.
Remove the RJ45-port cover from the tablet.
4.
Remove the two screws (M2x3) that secure the RJ45-port bezel to the tablet.
5.
Remove the RJ45-port assembly away from the tablet.
Installing the RJ45-port assembly
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
Removing and installing components
45