Dell Latitude 7230 Rugged Extreme Tablet Service Manual - Page 46

Blank top-cover, Removing the blank top-cover

Get Dell Latitude 7230 Rugged Extreme Tablet PDF manuals and user guides View all Dell Latitude 7230 Rugged Extreme Tablet manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

About this task The figure indicates the location of the RJ45-port assembly and provides a visual representation of the installation procedure. Steps NOTE: For models shipped with an expansion bay at the top side of the tablet. 1. Align the screw holes on the RJ45-port assembly with the screw holes on the tablet. 2. Replace the two screws (M2x3) to secure the RJ45-port assembly in place. 3. Align the screw holes on the RJ45-port cover with the screw holes on the RJ45-port assembly. 4. Replace the four screws (M2x5) to secure the RJ45-port cover to the RJ45-port assembly. 5. Connect the RJ45 FPC to the connector on the RJ45 daughter-board and close the latch. Next steps 1. Install the back-cover assembly. 2. Install the batteries. 3. Install the handle (for models shipped with handle). 4. Install the stylus. 5. Follow the procedure in after working inside your tablet. Blank top-cover Removing the blank top-cover Prerequisites 1. Follow the procedure in before working inside your tablet. 2. Remove the stylus. 3. Remove the handle (for the models shipped with a handle). 4. Remove the batteries. 5. Remove the back-cover assembly. 46 Removing and installing components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
About this task
The figure indicates the location of the RJ45-port assembly and provides a visual representation of the installation procedure.
Steps
NOTE:
For models shipped with an expansion bay at the top side of the tablet.
1.
Align the screw holes on the RJ45-port assembly with the screw holes on the tablet.
2.
Replace the two screws (M2x3) to secure the RJ45-port assembly in place.
3.
Align the screw holes on the RJ45-port cover with the screw holes on the RJ45-port assembly.
4.
Replace the four screws (M2x5) to secure the RJ45-port cover to the RJ45-port assembly.
5.
Connect the RJ45 FPC to the connector on the RJ45 daughter-board and close the latch.
Next steps
1.
Install the
back-cover assembly
.
2.
Install the
batteries
.
3.
Install the
handle
(for models shipped with handle).
4.
Install the
stylus
.
5.
Follow the procedure in
after working inside your tablet
.
Blank top-cover
Removing the blank top-cover
Prerequisites
1.
Follow the procedure in
before working inside your tablet
.
2.
Remove the
stylus
.
3.
Remove the
handle
(for the models shipped with a handle).
4.
Remove the
batteries
.
5.
Remove the
back-cover assembly
.
46
Removing and installing components