Dell Precision R5400 Remote Access Device: Administrator's User Manual&
Dell Precision R5400 Manual
View all Dell Precision R5400 manuals
Add to My Manuals
Save this manual to your list of manuals |
Dell Precision R5400 manual content summary:
- Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 1
TER0606004 TERA1x00 PC-over-IP® Administrative Interface User Manual May 26, 2008 Revision 3 Teradici Corporation 500 - 4400 Dominion St. Burnaby, BC, Canada V5G 4G3 Abstract This document describes administration interfaces of the PC-over- - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 2
TERA1x00 PC-over-IP Administrative Interface User Manual TER0606004 Issue 3 Revision History Version Date 1.0 January 15, 2008 2.0 • Added Time web configuration (see Section 1.5.11) • Added Firmware Part Number in Version web information (see Section 1.8.1.1) • Updated Firmware Upload build - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 3
TERA1x00 PC-over-IP Administrative Interface User Manual TER0606004 Issue 3 concerning PC-over-IP Half-Duplex in compatibility (Section 1.5.1.7) • Clarified when Device Bandwidth Limit and Device Bandwidth Target are applied (Section 1.5.5) • Updated USB - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 4
...30 1.5.9 Image...31 1.5.10 Monitor Emulation 33 1.5.11 Time...33 1.5.12 Password ...35 1.5.13 Reset Parameters 36 1.6 Permissions 37 1.6.1 USB ...37 1.6.2 Audio...40 1.6.3 Power...40 1.7 Diagnostics 41 1.7.1 Event Log...42 1.7.2 Session Control 43 © 2008 Teradici Corporation - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 5
Interface User Manual TER0606004 Issue 3 1.7.3 Session Statistics 44 1.7.4 Host CPU...46 1.7.5 Audio...48 1.7.6 Display ...48 1.7.7 Display (OSD 57 2.1 Connect Screen 57 2.1.1 Connect Button 58 2.2 2.3 2.3.1 OSD Options Menu 58 Configuration 59 Network...60 2.3.2 Connection - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 6
Manual TER0606004 Issue 3 3.1 Network Connection Lost Overlay 81 3.2 USB Device Not Authorized Overlay 81 4 Appendix A: Usage Examples 82 4.1 Peer-to-Peer Direct Connection 105 5 Appendix B: TERA1100 Portal Language and Keyboard Support 108 6 Appendix C: TERA1100 RDP Compatibility 110 - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 7
Webpage 40 Figure 22: Power Permissions Webpage 41 Figure 23: Diagnostics Menu Navigation 42 Figure 24: Event Log Webpage 42 Figure 25: Session Control Webpage 43 Figure 26: Session Statistics Webpage 45 Figure 27: Host CPU Webpage 47 Figure 28: Audio Diagnostics Webpage 48 Figure 29 - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 8
PC-over-IP Administrative Interface User Manual TER0606004 Issue 3 Figure 34: Upload Menu Navigation 54 Figure 35: Firmware Upload Webpage 54 Figure 36: OSD Logo Upload Webpage 56 Figure 37: OSD Connect Screen 57 Figure 38: OSD Connect Screen (Connecting 58 Figure 39: OSD Options Menu - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 9
Manual TER0606004 Issue 3 Figure 69: Portal Network Webpage DHCP Configuration 90 Figure 70: Portal PCoIP Processor Webpage DHCP & Discovery Configuration..... 91 Figure 71: Host Connection User Bandwidth Requirements (no limit 102 Figure 83: USB Permissions Example: Add new Button 102 Figure - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 10
TERA1x00 PC-over-IP Administrative Interface User Manual TER0606004 Issue 3 Tables Table 1: Connection Manager Method 21 Table 2: Peer 14: Firmware Information 77 Table 15: TERA1100 Supported Languages 108 Table 16: TERA1100 Supported Keyboard Layouts 108 Table 17: TERA1100 RDP Capabilities - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 11
connection management server Connection Management Server - an external management entity (3rd party) that manages and controls the Portal/Host through the CMI interface Display Data Channel Dynamic Host Configuration Protocol Domain Name System Domain Name System Service Record Extended Display - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 12
Display (OSD). As well, messages are displayed over the user screen when required. Users can connect/disconnect a session and view diagnostics 1 details the PC-over-IP Administrative Web Interface • Section 2 reviews On Screen Display (OSD) of the Portal • Section 3 discusses the user message - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 13
TERA1x00 PC-over-IP Administrative Interface User Manual TER0606004 Issue 3 1 Administrative Web Interface The and/or displayed parameters (inline help is displayed when appropriate) • Apply/Cancel - Each webpage with editable parameters has an Apply button and a Cancel button ○ Selecting - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 14
TERA1x00 PC-over-IP Administrative Interface User Manual Figure 1: Administration Web Interface TER0606004 Issue 3 1.1 Supported Web Browsers The webpage server on the TERA1x00 devices has been tested and is compatible with the following web browsers: • Firefox 1.5 and 2.0 • Internet Explorer 6.0 - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 15
Manual TER0606004 Issue 3 • Static IP Address: the IP address are hard coded and must be known • Dynamic IP Address: the IP address is dynamically assigned by the Dynamic Host Configuration Protocol (DHCP) server password. The HTTPS connection is secured using a Teradici self-signed certificate. - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 16
IP Administrative Interface User Manual Figure 2: Log In Webpage TER0606004 Issue 3 1.4.1 Warning The Warning displays pertinent information regarding the . As only one administrator is allowed per device, it displays administration session information. Logging into a session will terminate any - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 17
TERA1x00 PC-over-IP Administrative Interface User Manual • Connection Management • Discovery • Session • Bandwidth • RDP • Language • OSD • Image • Monitor Emulation • Time • Password • Reset Parameters Figure 3: Configuration Menu Navigation TER0606004 Issue 3 1.5.1 Network The Network webpage - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 18
When the Enable DHCP option is enabled, the device will contact a DHCP server to be assigned an IP address, subnet mask, gateway IP address and DNS servers. When disabled, the device requires these parameters to be set manually. 1.5.1.2 IP Address The IP Address is the device's IP address. If DHCP - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 19
Manual TER0606004 Issue 3 1.5.1.4 Gateway The Gateway is the device's gateway IP address. If DHCP is disabled, this field is required the DNS server IP Address is configured when using a Connection Manager, the Connection Manager address -Duplex. Half-Duplex is not supported by PC-over-IP and the - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 20
webpage allows enabling or disabling connection management, and to specify the IP address of the connection manager. In a managed connection, an external Connection Manager Server communicates with and can remotely control and configure the device. Additionally, the connection manager can locate an - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 21
User Manual TER0606004 Issue 3 Figure 6: Connection Management Configuration Webpage (FQDN) 1.5.2.1 Enable Connection Management If Enable Connection Management option is enabled, the device can be configured and controlled by an external connection manager. 1.5.2.2 Identify Connection Manager - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 22
Manual TER0606004 Issue 3 1.5.2.4 Enable Diagnostic Log The Enable Diagnostic Log field allows enabling diagnostic event log messages to log normal Connection Management Interface (CMI) server discovered by SLP management entities, without requiring prior knowledge of their locations in the - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 23
Manual TER0606004 Issue 3 When enabled, the Portal is able to display up to 10 available hosts in order of being discovered. It is expected that the Enable Host Discovery feature will be used with small numbers without requiring prior knowledge device connects to or accepts connections from peer - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 24
TERA1x00 PC-over-IP Administrative Interface User Manual Figure 8: Session Configuration Webpage TER0606004 Issue 3 © 2008 Teradici Corporation Page 24 of 111 - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 25
TERA1x00 PC-over-IP Administrative Interface User Manual Figure 9: Session Configuration Webpage (RDP) TER0606004 Issue 3 1.5.4.1 Accept Any Peer If the Accept Any Peer option is enabled, the host will accept connections from any Portal. If this option is disabled, the administrator must specify - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 26
IP Administrative Interface User Manual TER0606004 Issue 3 (FQDN). If Accept Any Peer is enabled, these fields are not required and are not editable option allows the Portal to automatically reconnect with the last connected Host after a power-cycle. This option is only available on a Portal; - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 27
Interface User Manual Figure 10: The PC-over-IP system will continue to use only the bandwidth required up to the Device Bandwidth Limit maximum. Due to normal usage to set Device Bandwidth Limit to the limit of the network connected to the Portal and Host. See Section 4.3 Bandwidth and Image - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 28
the network topology is required before setting this to a non-zero value. Note: The Device Bandwidth Tarket is applied when a new PC-over-IP session is started after selecting Apply. 1.5.6 RDP The RDP webpage allows configuration of the Remote Desktop Protocol (RDP) specific device settings. For - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 29
the RDP session colour bit depth. Possible values are: • 8 bpp (bits per pixel) • 16 bpp • 24 bpp 1.5.6.3 Terminal Server Port The Terminal Server Port sets the port number that the RDP client connects to. 1.5.6.4 Audio Mode The Audio Mode field configures where the audio playback occurs for the - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 30
the keyboard layout. Refer to Table 16 in Section 5 Appendix B: TERA1100 Portal Language and Keyboard Support for supported keyboard layouts. 1.5.8 OSD The OSD webpage allows modifying the On Screen Display (OSD) parameters. This option is only available on a Portal; on the Host it is disabled - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 31
TERA1x00 PC-over-IP Administrative Interface User Manual Figure 13: OSD Configuration Webpage TER0606004 Issue 3 1.5.8.1 Screen-Saver Message The Screen-Saver Message field allows the changing the OSD screen-saver text. The text - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 32
TERA1x00 PC-over-IP Administrative Interface User Manual Figure 14: Image Configuration Webpage TER0606004 Issue 3 1.5.9.1 Minimum Image Quality The Minimum Image Quality slider allows balancing between image quality and frame rate when network - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 33
will only respond to Display Data Channel (DDC) when in a PC-over-IP session. When Enable Monitor Emulation is enabled, the Host will use emulated data for DDC queries regardless if in a PC-over-IP session of not. There are Enable Monitor Emulation fields for both monitor ports available, DVI 1 and - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 34
Interface User Manual Figure 16: Time Configuration Webpage TER0606004 Issue 3 1.5.11.1 Current Time The Current time field displays the time Domain Name (FQDN). If NTP is disabled, this field is not required and is not editable. Table 3 shows the configuration parameters available when either - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 35
TERA1x00 PC-over-IP Administrative Interface User Manual TER0606004 Issue 3 1.5.11.4 NTP Host Port The NTP Host Port field configures the NTP port number. 1.5.11.5 NTP Query Interval The NTP Query Interval fields allow configuration of the query interval. The first field denotes the interval - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 36
TERA1x00 PC-over-IP Administrative Interface User Manual TER0606004 Issue 3 1.5.12.1 Old Password The Old Password field 1.5.13.1 Reset Parameters The Reset Parameters button resets all configuration and permissions to factory default values. When this button is selected, the web interface will - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 37
Manual TER0606004 Issue 3 1.6 Permissions The Permissions menu contains links to pages that define the range of functionality exposed to the user. The webpages in the Permissions menu are: • USB • Audio • Power (or 'any') can reduce the number of entries necessary to define all authorized - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 38
Manual Figure 20: USB Permissions Webpage TER0606004 Issue 3 1.6.1.1 Authorized Devices The Authorized Devices section allows specifying the authorized USB devices for the Portal. There are two buttons Entry Types Entry Type Required Hexadecimal Value Fields Comments © 2008 Teradici Corporation Page - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 39
User Manual TER0606004 buttons to allow customization of this "black list". The Add new button allows adding a new device or device group, while the Remove button allows its removal. Selecting the Add new button Unauthorization Entry Types Entry Type Required Hexadecimal Value Fields Comments - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 40
TERA1x00 PC-over-IP Administrative Interface User Manual TER0606004 Issue 3 Sub Class Protocol 0-FF, asterisk (*) indicates any to reduce the data bandwidth used for audio. 1.6.3 Power The Power webpage allows configuration of the power-off permissions of the Portal. © 2008 Teradici Corporation - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 41
and non-editable. 1.7 Diagnostics The Diagnostics menu contains links to pages with run-time information and functions that may be useful for troubleshooting. The webpages in the Diagnostics menu are: • Event Log • Session Control • Session Statistics • Host CPU • Audio • Display • PCoIP Processor - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 42
User Manual Figure 23: Diagnostics Menu Navigation TER0606004 Issue 3 1.7.1 Event Log The Event Log webpage allows viewing and clearing of the event log messages from the Portal or Host. Note: The Portal Event Log can also be viewed using the Portal OSD. See Section 2.4.1 Event Log. Figure 24 - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 43
Interface User Manual TER0606004 Issue 3 Clear Selecting the Clear button deletes all of the stored event log messages. 1.7.1.2 Event log filter mode The Event log filter mode pull-down menu allows filtering the event log. The options are: • Verbose • Terse 1.7.2 Session Control The Session - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 44
TERA1x00 PC-over-IP Administrative Interface User Manual TER0606004 Issue 3 Below the Connection State field there are two buttons; Connect and Disconnect. Connect If the Connection State is Disconnected, selecting this button causes the Portal to initiate a PC-over-IP session with its peer - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 45
State field reports the current state of the PC-over-IP session. Connection State values are: • Disconnected • Connection Pending • Connected 1.7.3.2 PCoIP Packets Statistics PCoIP Packets Sent PCoIP Packets Sent reports the total number of PC-over-IP packets sent in the current session. PCoIP - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 46
Manual TER0606004 Issue 3 1.7.3.3 Bytes Statistics Bytes Sent Bytes Sent reports the total number of bytes sent in the current session. Bytes Received Bytes Received reports the total number per second is 0 fps. 1.7.4 Host CPU The Host CPU webpage allows viewing and modifying of the Host - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 47
changing of the host power state. The options are: • S5 (Soft Off) • S5 (Hard Off) Note: This requires the appropriate Host hardware configuration. This option is only available on a Host; on the Portal it is disabled and non-editable. 1.7.4.4 Reset host CPU The Reset Host CPU button allows reset of - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 48
are two buttons available: The Start button starts the test tone, while the Stop button stops the test tone. This option is only available on a Portal; on the Host it is disabled and non-editable. 1.7.6 Display The Display webpage allows displaying a test pattern on the Portal displays. This option - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 49
Manual Figure 29: Display Webpage TER0606004 Issue 3 1.7.6.1 Test mode The Test Mode pull-down menu allows enabling a test pattern on the attached monitor(s). The test pattern options are • Video Test Stop The Start button starts the test pattern, while the Stop button stops the test pattern. This - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 50
Manual TER0606004 Issue 3 1.7.7 PCoIP Processor The Reset PCoIP Processor Reset button allows resetting the device processor. Figure 30: PCoIP Processor Webpage 1.7.7.1 Current Time The Current Time field displays the current time. This feature requires PCoIP Processor button allows resetting - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 51
TERA1x00 PC-over-IP Administrative Interface User Manual Figure 31: Info Menu Navigation TER0606004 Issue 3 1.8.1 Version The Version webpage allows viewing of hardware and firmware version information. Note: A subset of Portal Version information - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 52
Manual TER0606004 Issue 3 Table 6: VPD Information MAC Address TERA1x00 Portal/Host unique MAC address Unique Identifier TERA1x00 Portal/Host unique identifier Serial Number TERA1x00 Portal/Host unique serial number Firmware Part Number Part number code Processor Revision code reports the code - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 53
-over-IP Administrative Interface User Manual Figure 33: Attached Devices Webpage TER0606004 Issue 3 1.8.2.1 Monitors The Monitors section reports the Name, Serial Number, Vendor Identification (VID), Product Identification (PID), Date and Status the monitor attached to each port. The first line - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 54
TERA1x00 PC-over-IP Administrative Interface User Manual TER0606004 Issue 3 This option is only available on the firmware image to be uploaded. The administrator can browse to the file via the Browse button. The file must be accessible to the web browser (i.e., on a local or accessible network - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 55
-IP Administrative Interface User Manual TER0606004 Issue 3 1.9.1.2 Upload Selecting the Upload button will cause the specified upload of an image to the device. This image is displayed on the connect window of the local GUI On Screen Display (OSD) Logo. This option is only available on a Portal - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 56
network drive). The 24 bits per pixel image must be either JPG or BMP format, and dimensions cannot exceed 256 pixels in width, 64 pixels in height. If the file extension is incorrect, the web interface will display an error message. 1.9.2.2 Upload Selecting the Upload button will cause the - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 57
the Options button on the Connect Screen. An administrative password is required to change Portal options. 2.1 Connect Screen The Connect Screen is shown on startup except when the Portal has been configured for a managed start-up or auto-reconnect. The logo displayed above the Connect button can be - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 58
User Manual TER0606004 Issue 3 2.1.1 Connect Button A user can select the Connect button to initiate a PC-over-IP or RDP session depending on the session settings. While the PC-over-IP connection is pending, the OSD local GUI will display a "Connection Pending" message. When the connection is - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 59
its environment. The tabs in the Configuration window are: • Network • Connection Management • Discovery • Session • Bandwidth • RDP • Language • OSD • Reset All settings in the configuration tabs are password protected. Select the Unlock button in the bottom left corner of the Configuration window - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 60
TERA1x00 PC-over-IP Administrative Interface User Manual Figure 40: Setting Unlock OSD TER0606004 Issue 3 2.3.1 Network The Network tab allows an administrator to set the Portal network parameters. Note: The Network parameters can - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 61
Enable DHCP When Enable DHCP is enabled, the device will contact a DHCP server to be assigned an IP address, subnet mask, gateway IP address and DNS servers. When disabled, the device requires these parameters to be set manually. 2.3.1.2 IP Address The IP Address field is the device's IP address. If - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 62
to specify the IP address of the connection manager. In a managed connection, an external Connection Manager Server communicates with and can remotely control and configure the device. Additionally, the connection manager can locate an appropriate peer for the device to connect to, and initiate the - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 63
Interface User Manual Figure 42: Connection Management Configuration TER0606004 Issue 3 2.3.2.1 Enable Connection Management If the Enable Connection Management option is enabled, the device can be configured and controlled by an external connection manager. 2.3.2.2 Identify Connection Manager - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 64
Manual TER0606004 Issue 3 2.3.2.4 Enable Diagnostic Log The Enable Diagnostic Log field allows enabling diagnostic event log messages to log normal Connection Management Interface (CMI) server without requiring prior knowledge , the Portal is able to display up to 10 available hosts in order - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 65
TERA1x00 PC-over-IP Administrative Interface User Manual TER0606004 Issue 3 2.3.4 Session The Session tab allows an administrator to configure how the device connects to or accepts connections from peer devices. Note: The Session parameters can also be configured using the Webpage Administration - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 66
Interface User Manual TER0606004 Issue 3 Peer FQDN Peer MAC Address Peer FQDN PC-over-IP Used with Portal RDP client only 2.3.4.3 Enable Auto-Reconnect The Enable Auto-Reconnect option allows the Portal to automatically reconnect with the last connected Host after a power-cycle. 2.3.4.4 Session - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 67
Manual TER0606004 Issue 3 Due to normal usage scenarios, this allows effective bandwidth sharing, as it is unlikely that all PC-over-IP sessions will require RDP tab allows configuration of the Remote Desktop Protocol (RDP) specific device settings. For information on the TERA1100 RDP client, see - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 68
Interface User Manual TER0606004 Issue 3 2.3.6.2 Bit Depth The Bit Depth is the RDP session colour bit depth. Possible values are: • 8 bpp (bits per pixel) • 16 bpp • 24 bpp 2.3.6.3 Terminal Server Port The Terminal Server Port field sets the port number that the RDP client connects to - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 69
keyboard layout. Refer to Table 16 in Section 5 Appendix B: TERA1100 Portal Language and Keyboard Support for supported keyboard layouts. 2.3.8 OSD The OSD tab allows modifying the On Screen Display (OSD) parameters. Note: The OSD parameters can also be configured using the Webpage Administration - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 70
TERA1x00 PC-over-IP Administrative Interface User Manual Figure 48: OSD Configuration TER0606004 Issue 3 2.3.8.1 Screen-Saver Message The Screen-Saver Message field allows the changing the OSD screen-saver text. The text can - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 71
TERA1x00 PC-over-IP Administrative Interface User Manual Figure 49: Reset TER0606004 Issue 3 2.3.9.1 Reset Parameters The Reset Parameters Reset button resets all configuration and permissions to factory default values. When this button is selected, the OSD will prompt the administrator for - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 72
available. Refresh Selecting the Refresh button refreshes event log messages displayed. Clear Selecting the Clear button clears all of the displayed event log messages. 2.4.2 Session Statistics The Session Statistics tab allows viewing of PC-over-IP specific statistics. Note: Session Statistics can - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 73
TERA1x00 PC-over-IP Administrative Interface User Manual Figure 51: Session Statistics TER0606004 Issue 3 2.4.2.1 PCoIP Packets Statistics PCoIP Packets Sent The PCoIP Packets Sent field reports the total number of PC-over-IP packets sent from the Portal to the Host in the last active session. - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 74
TERA1x00 PC-over-IP Administrative Interface User Manual TER0606004 Issue 3 2.4.2.3 Round Trip Latency The Round Trip Latency field reports the total round-trip PC-over-IP system (e.g. Portal to Host, and back to - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 75
-IP Administrative Interface User Manual Figure 53: Ping TER0606004 Issue 3 2.4.4.1 Ping Settings IP Address IP Address to ping Interval Interval between ping packets Packet Size Size of ping packet 2.4.4.2 Packets Sent Number of ping packets sent Received Number of ping packets received - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 76
Administrative Interface User Manual Figure 54: Number Portal unique serial number Firmware Part Number Part number of PC-over-IP firmware Hardware Version Portal hardware version number Revision field reports the PC-over-IP Processor Revision code. TERA1x00 Revision A silicon is denoted by 0.0, - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 77
Interface User Manual TER0606004 Issue 3 2.5.1.4 Bootloader Information The Bootloader information reflects the current PC-over-IP bootloader details. Table 14: Firmware Information Bootloader Version Version of current PC-over-IP bootloader Bootloader Build ID Revision code of current - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 78
Administrative Interface User Manual TER0606004 Issue 3 Mouse Speed The Mouse Speed field allows configuration of the Portal mouse cursor speed. . 2.6.2 Portal keyboard repeat rate. Repeat Settings Test Box The Repeat Settings Test Box field allows testing of the chosen keyboard settings. 2.6.3 - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 79
TERA1x00 PC-over-IP Administrative Interface User Manual TER0606004 Issue 3 Note: The Image parameters can also be configured using the Webpage Administration Interface. See Section 1.5.9.1 Minimum Image Quality. Figure 57: Image Minimum Image - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 80
TERA1x00 PC-over-IP Administrative Interface User Manual Figure 58: Change Password TER0606004 Issue 3 Old Password The Old Password field must match the current administrative password for the change to take place. New - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 81
and text. The overlays have simple animation and are displayed when the status changes (i.e., the network connection becomes lost, or an unauthorized USB device is plugged in). 3.1 Network Connection Lost Overlay Loss of network connectivity is indicated using an overlay with the message "Network - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 82
Manual TER0606004 Issue 3 4 Appendix A: Usage Examples 4.1 Peer-to-Peer Direct Connection Example This example overviews configuring the Portal and Host for a direction connection, i.e. without the use of a Connection Management Server Peer-to-Peer direct connection, it is required to know the IP - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 83
TERA1x00 PC-over-IP Administrative Interface User Manual TER0606004 Issue 3 Figure 61: Portal Connection Management Peer-to-Peer Configuration 4. Ensure Enable Connection Management is not selected 5. Select the Session webpage from the Configuration menu © 2008 Teradici Corporation Page 83 of - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 84
TERA1x00 PC-over-IP Administrative Interface User Manual TER0606004 Issue 3 Figure 62: Portal Session Webpage Peer-to-Peer Configuration 6. Select IP in Peer MAC Address field, e.g. 00-19-D2-6F- EC-6C 9. Select the Apply button to accept the changes 10. Select the PCoIP Processor webpage from the - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 85
-IP Administrative Interface User Manual TER0606004 Issue 3 Figure 63: Portal PCoIP Processor Webpage Peer-to-Peer Configuration 11. Select the Reset button to reset the PC-over-IP processor 4.1.2 Host Peer-to-Peer Configuration Configure the Host for peer-to-peer direct connection: 12. Open the - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 86
TERA1x00 PC-over-IP Administrative Interface User Manual TER0606004 Issue 3 Figure 64: Host Connection Management Peer-to-Peer Configuration 15. Ensure Enable Connection Management is not selected 16. Select the Session webpage from the Configuration menu © 2008 Teradici Corporation Page 86 of - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 87
TERA1x00 PC-over-IP Administrative Interface User Manual TER0606004 Issue 3 Figure 65: Host Session -D2- 19-00 20. Select the Apply button to accept the changes 4.1.3 Initiating Peer-to-Peer Session Start the peer-to-peer session: 1. Select the Connect button to start the PC-over-IP session © - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 88
Connection Management Server. The following starting IP addresses are used for this example: • Portal: IP Address: 192.168.0.111 • Host: IP Address: 192.168.1.222 Note: To configure for DHCP and Host Discovery, it is required . See Section 2 On Screen Display (OSD) for matching OSD functionality - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 89
TERA1x00 PC-over-IP Administrative Interface User Manual TER0606004 Issue 3 2. Log in to the Portal Administration Web Interface 3. Select the Connection Management webpage from the Configuration menu Figure 67: Portal Connection Management DHCP & Discovery Configuration 4. Ensure Enable - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 90
Administrative Interface User Manual TER0606004 Issue 3 6. Select Enable Discovery and Enable Host Discovery 7. Select the Apply button to accept the changes DHCP Configuration 10. Select Enable DHCP 11. Select the Apply button to accept the changes Note: Once configured for DHCP, the IP address - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 91
Interface User Manual TER0606004 Issue 3 Figure 70: Portal PCoIP Processor Webpage DHCP & Discovery Configuration 13. Select the Reset button to reset Administration Web Interface 3. Select the Connection Management webpage from the Configuration menu © 2008 Teradici Corporation Page 91 of - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 92
DHCP & Discovery Configuration 4. Ensure Enable Connection Management is not selected 5. Select the Discovery webpage from the Configuration menu Figure 72: Host Discovery Webpage Enable Discovery Configuration 6. Select Enable Discovery 7. Select the Apply button to accept the changes 8. Select - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 93
IP Administrative Interface User Manual Figure 73: Host Network Webpage DHCP Configuration TER0606004 Issue 3 9. Select Enable DHCP 10. Select the Apply button to accept the changes Note: Once configured for DHCP, the IP address will be leased from the DHCP server. For future configuration, obtain - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 94
the Host PC restarts, enters standby, hibernates or powers off. 4.2.3 Initiating DHCP Discovery Session Start the DHCP discovery session: 1. Select the Connect button to start the discovering available hosts Figure 75: DHCP Discovery Connect Screen 2. Select the desired host from the Discovered - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 95
IP Administrative Interface User Manual Figure 76: Discovered Hosts Screen TER0606004 Issue 3 3. When connected, the Host computer do not require heavy graphics changes and would each likely require peak network demand at different times. Figure 77 shows simplified bandwidth requirements for each - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 96
over-IP Administrative Interface User Manual TER0606004 Issue 3 Figure 77: Simplified User Bandwidth Requirements (Assuming 100 Mbps) to be imperceptible to the user. However, in some low-bandwidth or high network latency situations, it might be preferable to eliminate congestion-based packet - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 97
Manual TER0606004 Issue 3 3. Select the Bandwidth webpage from the Configuration menu Figure 78: Host Bandwidth Limit Configuration (25 Mbps) 4. Enter 25 in the Device Bandwidth Limited field 5. Enter 20 in the Device Bandwidth Target field 6. Select the Apply button bandwidth when required. It - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 98
Manual TER0606004 Issue 3 Figure 79: Simplified User Bandwidth Requirements (25 Mbps) 4.3.2 Configuring Image Properties The PC-over-IP system gives two controls that users may occasionally require more bandwidth than is available to fully render their display information at maximum quality and - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 99
Manual TER0606004 Issue 3 default setting of 90 can reduce the amount of bandwidth required to configure the Portal. See Section 2 On Screen Display (OSD) for matching OSD functionality. The Maximum Initial slider to the right 6. Select the Apply button to accept the changes 7. Repeat for the - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 100
initial video frame). A higher Maximum Initial Image Quality setting requires more bandwidth as the higher quality initial image will require more bandwidth to create. The PC-over-IP system will always build unchanged regions of the display to a lossless image regardless of the Maximum Initial Image - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 101
to enable no limit 6. Select the Apply button to accept the changes 7. Repeat for the other three user Hosts The bandwidth limit and target are now set to 0 Mbps (no limit) for each user. Due to the nature of the task workers usage: light graphics changes and peak network demand different times - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 102
User Manual TER0606004 Issue 3 Figure 82: Simplified User Bandwidth Requirements (no limit) 4.4 USB Permissions Example This example illustrates the usage of the USB Permissions webpage. Here is shown how an administrator can use the human-readable drop down menus to authorize a specific class - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 103
TERA1x00 PC-over-IP Administrative Interface User Manual TER0606004 Issue 3 Figure 84: USB Permissions Example: Selecting the Class Entry Type 3. Next the Device Class must be selected. As the intent is to authorize a - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 104
TERA1x00 PC-over-IP Administrative Interface User Manual TER0606004 Issue 3 4. Next the sub class must be selected. Because the intent is to authorize a specific class of printers, select Printer. Otherwise, the sub class and protocol could be left as Any. Figure 86: USB Permissions Example: - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 105
Interface User Manual TER0606004 Issue 3 6. Select Add to save the changes to FLASH to complete the configuration. Figure 88: USB Authorization Example: Class Authorization 4.4.2 Authorizing USB Device By Vendor/Product ID 1. In the Authorization section, select Add new button. Figure 89 - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 106
TERA1x00 PC-over-IP Administrative Interface User Manual TER0606004 Issue 3 Figure 90: USB Permissions Example: Selecting the Class Entry Type 3. Enter the USB device Vendor ID and Product ID. Figure 91: USB Permissions - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 107
TERA1x00 PC-over-IP Administrative Interface User Manual TER0606004 Issue 3 4. Select Add to save the changes to FLASH to complete the configuration. Figure 92: USB Permissions Example: Vendor ID and Product ID Authorization © 2008 Teradici Corporation Page 107 of 111 - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 108
TERA1x00 PC-over-IP Administrative Interface User Manual TER0606004 Issue 3 5 Appendix B: TERA1100 Portal Language and Keyboard Support The TERA1100 Portal Firmware can support various languages and keyboard layouts. Information concerning configuring the language and keyboard layout can be found - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 109
TERA1x00 PC-over-IP Administrative Interface User Manual TER0606004 Issue 3 Latin American Latin American (accent keys) Portuguese ISO-8859-1 Portuguese ISO-8859-1 of America Emacs optimized layout United States of America Traditional Unix Workstation © 2008 Teradici Corporation Page 109 of 111 - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 110
RDP Protocol Version 5.2 Supported Terminal Servers Windows XP, Vista, & Server 2003 Display Resolution (single monitor) 800x600, 1024x768, 1280x768, 1280x1024, 1440x900, 1600x1200, 1680x1050, 1920x1200, Color Depth 8, 16, 24 bits per pixel RDP Port Configurable (default 3389) Audio - Dell Precision R5400 | Remote Access Device: Administrator's
User Manual& - Page 111
TERA1x00 PC-over-IP Administrative Interface User Manual TER0606004 Issue 3 © 2008 Teradici Corporation Page 111 of 111
© 2008 Teradici Corporation
TER0606004
TERA1x00 PC-over-IP®
Administrative
Interface
User
Manual
May 26, 2008
Revision 3
Teradici Corporation
500 – 4400 Dominion St.
Burnaby, BC, Canada V5G 4G3
Abstract
This document describes administration interfaces of the PC-over-IP
TM
Firmware for the TERA1100 and TERA1200
processors.