Dell Precision R5400 Remote Access Device: Administrator's User Manual& - Page 62

Primary DNS Server, 3.1.6 Secondary DNS Server, 3.1.7 Ethernet Mode

Get Dell Precision R5400 PDF manuals and user guides View all Dell Precision R5400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

TERA1x00 PC-over-IP Administrative Interface User Manual TER0606004 Issue 3 2.3.1.5 Primary DNS Server The Primary DNS Server field is the device's primary DNS IP address. If DHCP is disabled, this field is required. If DHCP is enabled, this field is not editable. This field must be a valid IP address, and if an invalid IP address is entered, the OSD will prompt the administrator to correct it. 2.3.1.6 Secondary DNS Server The Secondary DNS Server field is the device's secondary DNS IP address. If DHCP is disabled, this field is required. If DHCP is enabled, this field is not editable. This field must be a valid IP address, and if an invalid IP address is entered, the OSD will prompt the administrator to correct it. 2.3.1.7 Ethernet Mode The Ethernet Mode field configures the Ethernet mode of the Portal. The options are: • Auto • 10 Mbps Full-Duplex • 100 Mbps Full-Duplex Note: Users should always set the Ethernet Mode to Auto and only use 10 Mbps Full-Duplex or 100 Mbps Full-Duplex when the other network endpoint is also configured to operate at 10M Mbps Full-Duplex or 100M Mbps Full-Duplex. 2.3.2 Connection Management The Connection Management tab allows enabling or disabling connection management, and to specify the IP address of the connection manager. In a managed connection, an external Connection Manager Server communicates with and can remotely control and configure the device. Additionally, the connection manager can locate an appropriate peer for the device to connect to, and initiate the connection. Connection management can greatly simplify the administration effort for a large, complex system. Note: The Connection Management parameters can also be configured using the Webpage Administration Interface. See Section 1.5.2 Connection Management. © 2008 Teradici Corporation Page 62 of 111

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
TERA1x00 PC-over-IP Administrative Interface User Manual
TER0606004 Issue 3
© 2008 Teradici Corporation
Page 62 of 111
2.3.1.5 Primary DNS Server
The
Primary DNS Server
field is the device’s primary DNS IP address.
If DHCP is
disabled, this field is required.
If DHCP is enabled, this field is not editable.
This
field must be a valid IP address, and if an invalid IP address is entered, the OSD will
prompt the administrator to correct it.
2.3.1.6 Secondary DNS Server
The
Secondary DNS Server
field is the device’s secondary DNS IP address.
If
DHCP is disabled, this field is required.
If DHCP is enabled, this field is not editable.
This field must be a valid IP address, and if an invalid IP address is entered, the
OSD will prompt the administrator to correct it.
2.3.1.7 Ethernet Mode
The
Ethernet Mode
field configures the Ethernet mode of the Portal.
The options
are:
•
Auto
•
10 Mbps Full-Duplex
•
100 Mbps Full-Duplex
Note: Users should always set the
Ethernet Mode
to
Auto
and only use
10 Mbps
Full-Duplex
or
100 Mbps Full-Duplex
when the other network endpoint is also
configured to operate at 10M Mbps Full-Duplex or 100M Mbps Full-Duplex.
2.3.2
Connection Management
The
Connection Management
tab allows enabling or disabling connection
management, and to specify the IP address of the connection manager.
In a managed connection, an external Connection Manager Server communicates
with and can remotely control and configure the device.
Additionally, the connection
manager can locate an appropriate peer for the device to connect to, and initiate the
connection.
Connection management can greatly simplify the administration effort
for a large, complex system.
Note: The Connection Management parameters can also be configured using the
Webpage Administration Interface.
See Section 1.5.2 Connection Management.