Dell Precision R5400 Remote Access Device: Administrator's User Manual& - Page 61

Enable DHCP, 3.1.2 IP Address, 3.1.3 Subnet Mask, 3.1.4 Gateway

Get Dell Precision R5400 PDF manuals and user guides View all Dell Precision R5400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

TERA1x00 PC-over-IP Administrative Interface User Manual Figure 41: Network Configuration TER0606004 Issue 3 2.3.1.1 Enable DHCP When Enable DHCP is enabled, the device will contact a DHCP server to be assigned an IP address, subnet mask, gateway IP address and DNS servers. When disabled, the device requires these parameters to be set manually. 2.3.1.2 IP Address The IP Address field is the device's IP address. If DHCP is disabled, this field is required. If DHCP is enabled, this field is not editable. This field must be a valid IP address, and if an invalid IP address is entered, the OSD will prompt the administrator to correct it. 2.3.1.3 Subnet Mask The Subnet Mask field is the device's subnet mask. If DHCP is disabled, this field is required. If DHCP is enabled, this field is not editable. This field must be a valid subnet mask, and if an invalid subnet mask is entered, the OSD will prompt the administrator to correct it. 2.3.1.4 Gateway The Gateway field is the device's gateway IP address. If DHCP is disabled, this field is required. If DHCP is enabled, this field is not editable. This field must be a valid IP address, and if an invalid IP address is entered, the OSD will prompt the administrator to correct it. © 2008 Teradici Corporation Page 61 of 111

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
TERA1x00 PC-over-IP Administrative Interface User Manual
TER0606004 Issue 3
© 2008 Teradici Corporation
Page 61 of 111
Figure 41: Network Configuration
2.3.1.1 Enable DHCP
When
Enable DHCP
is enabled, the device will contact a DHCP server to be
assigned an IP address, subnet mask, gateway IP address and DNS servers.
When
disabled, the device requires these parameters to be set manually.
2.3.1.2 IP Address
The
IP Address
field is the device’s IP address.
If DHCP is disabled, this field is
required.
If DHCP is enabled, this field is not editable.
This field must be a valid IP
address, and if an invalid IP address is entered, the OSD will prompt the
administrator to correct it.
2.3.1.3 Subnet Mask
The
Subnet Mask
field is the device’s subnet mask.
If DHCP is disabled, this field is
required.
If DHCP is enabled, this field is not editable.
This field must be a valid
subnet mask, and if an invalid subnet mask is entered, the OSD will prompt the
administrator to correct it.
2.3.1.4 Gateway
The
Gateway
field is the device’s gateway IP address.
If DHCP is disabled, this field
is required.
If DHCP is enabled, this field is not editable.
This field must be a valid
IP address, and if an invalid IP address is entered, the OSD will prompt the
administrator to correct it.