Dell Precision R5400 Remote Access Device: Administrator's User Manual& - Page 33

Monitor Emulation, 5.11 Time

Get Dell Precision R5400 PDF manuals and user guides View all Dell Precision R5400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

TERA1x00 PC-over-IP Administrative Interface User Manual TER0606004 Issue 3 Note: The Maximum Initial Image Quality does not have a corresponding parameter on the Portal OSD, as it is intended as an administrator only parameter. 1.5.10 Monitor Emulation The Monitor Emulation webpage allows an enabling and disabling the monitor emulation feature. This option is only available on a Host; on the Portal it is disabled and non-editable. Figure 15: Monitor Emulation Configuration Webpage 1.5.10.1 Enable Monitor Emulation When Enable Monitor Emulation is disabled, the Host will only respond to Display Data Channel (DDC) when in a PC-over-IP session. When Enable Monitor Emulation is enabled, the Host will use emulated data for DDC queries regardless if in a PC-over-IP session of not. There are Enable Monitor Emulation fields for both monitor ports available, DVI 1 and DVI 2. 1.5.11 Time The Time webpage allows configuration of the Network Time Protocol (NTP) settings to allow the event logs (see Section 1.7.1 Event Log) of the Portal and Host to be time-stamped based on NTP time. © 2008 Teradici Corporation Page 33 of 111

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
TERA1x00 PC-over-IP Administrative Interface User Manual
TER0606004 Issue 3
© 2008 Teradici Corporation
Page 33 of 111
Note: The
Maximum Initial Image Quality
does not have a corresponding
parameter on the Portal OSD, as it is intended as an administrator only parameter.
1.5.10 Monitor Emulation
The
Monitor Emulation
webpage allows an enabling and disabling the monitor
emulation feature.
This option is only available on a Host; on the Portal it is disabled and non-editable.
Figure 15: Monitor Emulation Configuration Webpage
1.5.10.1 Enable Monitor Emulation
When
Enable Monitor Emulation
is disabled, the Host will only respond to Display
Data Channel (DDC) when in a PC-over-IP session.
When
Enable Monitor
Emulation
is enabled, the Host will use emulated data for DDC queries regardless if
in a PC-over-IP session of not.
There are
Enable Monitor Emulation
fields for both monitor ports available, DVI 1
and DVI 2.
1.5.11 Time
The
Time
webpage allows configuration of the Network Time Protocol (NTP) settings
to allow the event logs (see Section 1.7.1 Event Log) of the Portal and Host to be
time-stamped based on NTP time.