Dell Precision R5400 Remote Access Device: Administrator's User Manual& - Page 26

Enable Auto-Reconnect, 5.4.5 Session Timeout

Get Dell Precision R5400 PDF manuals and user guides View all Dell Precision R5400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

TERA1x00 PC-over-IP Administrative Interface User Manual TER0606004 Issue 3 (FQDN). If Accept Any Peer is enabled, these fields are not required and are not editable. Table 2 shows the peer identity parameters available when either method is chosen. If an invalid IP address or DNS name is entered, the web interface will prompt the administrator to correct it. Table 2: Peer Identity Methods Peer Identity Method Data Fields Peer IP/MAC Peer IP Address Peer FQDN Peer MAC Address Peer DNS Name Comment PC-over-IP or Portal RDP client PC-over-IP Used with Portal RDP client only Figure See Figure 8 See Figure 9 1.5.4.4 Enable Auto-Reconnect The Enable Auto-Reconnect option allows the Portal to automatically reconnect with the last connected Host after a power-cycle. This option is only available on a Portal; on the Host it is disabled and non-editable. 1.5.4.5 Session Timeout The Session Timeout configures the timeout for a connection of an active session. If the timeout period elapses without the PC-over-IP processor receiving data from its peer, the PC-over-IP processor will disconnect the session. 1.5.5 Bandwidth The Bandwidth webpage allows limiting the device bandwidth. Note: The Portal Bandwidth can also be configured using the Portal OSD. See Section 2.3.5 Bandwidth. © 2008 Teradici Corporation Page 26 of 111

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
TERA1x00 PC-over-IP Administrative Interface User Manual
TER0606004 Issue 3
© 2008 Teradici Corporation
Page 26 of 111
(FQDN).
If Accept Any Peer is enabled, these fields are not required and are not
editable.
Table 2 shows the peer identity parameters available when either method is chosen.
If an invalid IP address or DNS name is entered, the web interface will prompt the
administrator to correct it.
Table 2: Peer Identity Methods
Peer Identity Method
Data Fields
Comment
Figure
Peer IP Address
PC-over-IP or
Portal RDP client
Peer IP/MAC
Peer MAC Address
PC-over-IP
See Figure 8
Peer FQDN
Peer DNS Name
Used with Portal
RDP client only
See Figure 9
1.5.4.4 Enable Auto-Reconnect
The
Enable Auto-Reconnect
option allows the Portal to automatically reconnect
with the last connected Host after a power-cycle.
This option is only available on a Portal; on the Host it is disabled and non-editable.
1.5.4.5 Session Timeout
The
Session Timeout
configures the timeout for a connection of an active session.
If the timeout period elapses without the PC-over-IP processor receiving data from its
peer, the PC-over-IP processor will disconnect the session.
1.5.5
Bandwidth
The
Bandwidth
webpage allows limiting the device bandwidth.
Note: The Portal Bandwidth can also be configured using the Portal OSD.
See
Section 2.3.5 Bandwidth.