Epson LQ 870 User Manual - Page 47

paper into the desired paper slot front, bottom, or rear until - printer ribbon

Get Epson LQ 870 - B/W Dot-matrix Printer PDF manuals and user guides View all Epson LQ 870 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Using Continuous Paper 4. Slide the left sprocket unit to approximately 12 mm (OS inch) from the far left position (use the alignment marks on the printer case). Push the sprocket lock back to lock it in place. Then slide the right sprocket unit to match the width of your paper, but do not lock it. Move the paper support so it is midway between the sprocket units. 5. Make sure your paper has a clean, straight edge. Insert the paper into the desired paper slot (front, bottom, or rear) until it emerges between the platen and the ribbon guide. Pull the paper up until the perforation between the first and second pages is even with the top of the printer's ribbon. Paper Handling 2-19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
Using Continuous Paper
4.
Slide the left sprocket unit to approximately 12 mm
(OS
inch)
from the far left position (use the alignment marks on the
printer case). Push the sprocket lock back to lock it in place.
Then slide the right sprocket unit to match the width of your
paper, but do not lock it. Move the paper support so it is
midway between the sprocket units.
5.
Make sure your paper has a clean, straight edge. Insert the
paper into the desired paper slot (front, bottom, or rear) until it
emerges between the platen and the ribbon guide. Pull the
paper up until the perforation between the first and second
pages is even with the top of the printer’s ribbon.
Paper Handling
2-19