Epson TM-U950P Specifications - Page 43

ESC p, DLE EOT, ESC u, GS r, Table 2.2.2, Drawer Kick-out Connector Pin Assignments, - printer driver

Get Epson TM-U950P - B/W Dot-matrix Printer PDF manuals and user guides View all Epson TM-U950P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

2.2.3 Drawer kick-out connector (modular connector) The pulse specified by ESC p is output to this connector. The host can confirm the status of the input signal by using the DLE EOT, ESC u, GS r, or GS a (ASB) commands. 1) Pin assignments: Refer to Table 2.2.2. 2) Connector model: Printer side: MOLEX 52065-6615 or equivalent User side: 6-position 6-contact (RJ12 telephone jack) Table 2.2.2 Drawer Kick-out Connector Pin Assignments Pin Number Signal name Direction 1 Frame GND -- 2 Drawer Kick-out driver signal 1 Output 3 Drawer open/close signal Input 4 +24V -- 5 Drawer kick-out drive signal 2 Output 6 Signal GND -- 1 6 3) Drawer Kick-out drive signal Output signal: Output voltage: Approximately 24 V Output current: 1 A or less CAUTION: To avoid an overcurrent, the resistance of the drawer kick-out solenoid must be 24W or more. Output waveform: Outputs the waveforms in Figure 2.2.2 to the points A and B in Figure 2.2.3. t1 (ON time) and t2 (OFF time) are specified by ESC p. Figure 2.2.2 Drawer Kick-out Drive Signal Output Waveform TITLE EPSON TM-U950/U950P Specification (STANDARD) SHEET NO. REVISION AF NEXT 270 SHEET 2169

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
EPSON
TITLE
SHEET
REVISION
NO.
SHEET
NEXT
TM-U950/U950P
Specification
(STANDARD)
2.2.3 Drawer kick-out connector (modular connector)
The pulse specified by
ESC p
is output to this connector.
The host can confirm the status of the
input signal by using the
DLE EOT, ESC u, GS r,
or
GS a
(ASB) commands.
1) Pin assignments:
Refer to Table 2.2.2.
2) Connector model:
Printer side:
MOLEX 52065-6615 or equivalent
User side:
6-position 6-contact (RJ12 telephone jack)
Table 2.2.2
Drawer Kick-out Connector Pin Assignments
Pin Number
Signal name
Direction
1
Frame GND
--
2
Drawer Kick-out driver signal 1
Output
3
Drawer open/close signal
Input
4
+24V
--
5
Drawer kick-out drive signal 2
Output
6
Signal GND
--
3) Drawer Kick-out drive signal
Output signal:
Output voltage: Approximately 24 V
Output current:
1 A or less
CAUTION:
To avoid an overcurrent, the resistance of the drawer kick-out solenoid must be 24
W
or
more.
Output waveform:
Outputs the waveforms in Figure 2.2.2 to the points A and B in Figure
2.2.3.
t1
(ON time) and
t2
(OFF time) are specified by
ESC p
.
Figure 2.2.2
Drawer Kick-out Drive Signal Output Waveform
1
6
F
19
20