Garmin Edge 705 Owner's Manual - Page 47

Training with Cadence, GSC 10 Battery, Reset - speed cadence sensor

Get Garmin Edge 705 - Cycle GPS Receiver PDF manuals and user guides
UPC - 753759066956
View all Garmin Edge 705 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

5. Press the Reset button on the GSC 10. The LED turns red, then green. Pedal to test the sensor alignment. The red LED blinks each time the crank arm passes the sensor, and the green LED blinks each time the wheel magnet passes the sensor arm. note: The LED blinks for the first 60 passes after a reset. Press Reset again if you require additional passes. 6. When everything is aligned and working correctly, tighten the cable ties, sensor arm, and spoke magnet. Using Accessories Training with Cadence Cadence is your rate of pedaling or "spinning" measured by the number of revolutions of the crank arm per minute (rpm). There are two sensors on the GSC 10: one for cadence and one for speed. For information about cadence alerts, see page 19. For information about speed zones, see page 56. GSC 10 Battery For GSC 10 battery information, see page 61. Edge 605/705 Owner's Manual 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Edge 605/705 Owner’s Manual
µ²
U
SING
A
CCESSORIES
5. Press the
Reset
button on
the GSC 10. The LED turns
red, then green. Pedal to test
the sensor alignment. The
red LED blinks each time the
crank arm passes the sensor,
and the green LED blinks each
time the wheel magnet passes
the sensor arm.
NOTE:
The LED blinks
for the first 60 passes after
a reset. Press
Reset
again
if you require additional
passes.
6. When everything is aligned
and working correctly, tighten
the cable ties, sensor arm, and
spoke magnet.
Training with Cadence
Cadence is your rate of pedaling or
“spinning” measured by the number
of revolutions of the crank arm per
minute (rpm). There are two sensors
on the GSC 10: one for cadence and
one for speed.
For information about cadence alerts,
see
page 19
.
For information about speed zones,
see
page 56
.
GSC 10 Battery
For GSC 10 battery information, see
page 61
.