HP 3PAR StoreServ 7400 2-node HP 3PAR StoreServ 7000 Storage Service Guide - Page 27

State, Connected, Device Type, Connected Device Type, Interactive CLI for an InServ

Get HP 3PAR StoreServ 7400 2-node PDF manuals and user guides View all HP 3PAR StoreServ 7400 2-node manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Typically the State is listed as Loss sync, the Mode as Initiator and the Connected Device Type as Free. 3. Verify that the SFP has been successfully replaced by refreshing the above pane. State should now be listed as Ready, the Mode as Target and the Connected Device Type as Host. To perform maintenance using CLI, access SPMAINT: 1. In the 3PAR Service Processor Menu, select option 7 Interactive CLI for an InServ. 2. Issue the following commands: • showport to view the port State: s750 cli%showport N:S:P Mode State Node_WWN Port_WWN/HW_Addr Type Protocol Label Partner FailoverState 0:0:1 initiator ready 50002ACFF70185A6 50002AC0010185A6 disk SAS - - - 0:0:2 initiator ready 50002ACFF70185A6 50002AC0020185A6 disk SAS - - - 0:1:1 target ready 2FF70002AC0185A6 20110002AC0185A6 host FC - - - 0:1:2 target ready 2FF70002AC0185A6 20120002AC0185A6 host FC - - - 0:2:1 target loss_sync - 2C27D75301F6 iscsi iSCSI - - - 0:2:2 target loss_sync - 2C27D75301F2 iscsi iSCSI SFP Repair 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
Typically the
State
is listed as
Loss sync
, the
Mode
as
Initiator
and the
Connected
Device Type
as
Free
.
3.
Verify that the SFP has been successfully replaced by refreshing the above pane.
State
should now be listed as
Ready
, the
Mode
as
Target
and the
Connected Device Type
as
Host
.
To perform maintenance using CLI, access SPMAINT:
1.
In the 3PAR Service Processor Menu, select option
7 Interactive CLI for an InServ
.
2.
Issue the following commands:
•
showport
to view the port
State
:
s750 cli%showport
N:S:P
Mode
State
Node_WWN
Port_WWN/HW_Addr Type Protocol
Label Partner FailoverState
0:0:1 initiator
ready 50002ACFF70185A6 50002AC0010185A6 disk
SAS
-
-
-
0:0:2 initiator
ready 50002ACFF70185A6 50002AC0020185A6 disk
SAS
-
-
-
0:1:1
target
ready 2FF70002AC0185A6 20110002AC0185A6 host
FC
-
-
-
0:1:2
target
ready 2FF70002AC0185A6 20120002AC0185A6 host
FC
-
-
-
0:2:1
target loss_sync
- 2C27D75301F6
iscsi
iSCSI
-
-
-
0:2:2
target loss_sync
- 2C27D75301F2
iscsi
iSCSI
SFP Repair
27