HP 3PAR StoreServ 7400 2-node HP 3PAR StoreServ 7000 Storage Service Guide - Page 45

Service Processor Connector Pin-outs, Manually Initializing the Storage System Software

Get HP 3PAR StoreServ 7400 2-node PDF manuals and user guides View all HP 3PAR StoreServ 7400 2-node manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Figure 35 Maintenance PC Connector Pin-outs Service Processor Connector Pin-outs Use at the SP end of a standard Ethernet cable and in conjunction with the laptop adapter (PN 180-0055-01) to allow serial connection to the SP. DB9 (Female) RJ45 • Pin 2-Pin 3 (orange) • Pin 3-Pin 2 (black) • Pin 5-Pin 5 (green) Figure 36 Service Processor Connector Pin-outs Manually Initializing the Storage System Software Use the following procedures to manually set up the storage system and SP when access to the wizards is not available. NOTE: You must physically connect a laptop to the SP to complete these procedures. See the section "Connecting a Laptop to the SP" in the HP 3PAR StoreServ 7000 Storage Installation Guide. Manually Setting up the Storage System The Out-of-the-Box (OOTB) script guides you through setting up and configuring the storage system software: 1. Connect the PC to the controller node 0 through a serial cable and log in with user ID console. 2. From the Console Menu, select option 1, Out of The Box Procedure. 3PAR Console Menu 1400293-1 3.1.2.xxx 1. Out Of The Box Procedure 2. Run ootb-stress-analyzer 3. Re-enter network configuration 4. Update the CBIOS 5. Enable or disable CLI error injections 6. Perform an IDE rescue Manually Initializing the Storage System Software 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
Figure 35 Maintenance PC Connector Pin-outs
Service Processor Connector Pin-outs
Use at the SP end of a standard Ethernet cable and in conjunction with the laptop adapter (PN
180-0055-01) to allow serial connection to the SP.
DB9 (Female) RJ45
•
Pin 2-Pin 3 (orange)
•
Pin 3-Pin 2 (black)
•
Pin 5-Pin 5 (green)
Figure 36 Service Processor Connector Pin-outs
Manually Initializing the Storage System Software
Use the following procedures to manually set up the storage system and SP when access to the
wizards is not available.
NOTE:
You must physically connect a laptop to the SP to complete these procedures. See the
section “Connecting a Laptop to the SP” in the
HP 3PAR StoreServ 7000 Storage Installation Guide
.
Manually Setting up the Storage System
The Out-of-the-Box (OOTB) script guides you through setting up and configuring the storage system
software:
1.
Connect the PC to the controller node 0 through a serial cable and log in with user ID
console
.
2.
From the Console Menu, select option
1, Out of The Box Procedure
.
3PAR Console Menu 1400293-1 3.1.2.xxx
1. Out Of The Box Procedure
2. Run ootb-stress-analyzer
3. Re-enter network configuration
4. Update the CBIOS
5. Enable or disable CLI error injections
6. Perform an IDE rescue
Manually Initializing the Storage System Software
45