HP 3PAR StoreServ 7400 2-node HP 3PAR StoreServ 7000 Storage Service Guide - Page 48

Installing HP 3PAR OS Files, Insert the HP 3PAR OS Release Distribution CD into the SP.

Get HP 3PAR StoreServ 7400 2-node PDF manuals and user guides View all HP 3PAR StoreServ 7400 2-node manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

14. Verify the correct license is displayed and press Enter. If the license information is not correct, type c and press Enter to continue with the system setup. After completing the system setup, contact your local service provider for technical support to obtain the proper license keys. 15. Complete the network configuration: a. When prompted, type the number of IP addresses used by the system (usually 1) and press Enter. b. Type the IP address and press Enter. c. Type the netmask and press Enter. When prompted, press Enter again to accept the previously entered netmask. d. Type the gateway IP address and press Enter. e. Specify the speed and duplex and press Enter. Please specify speed (10, 100 or 1000) and duplex (half or full), or auto to use autonegotation: auto NOTE: If an NTP system IP address is not provided, use the SP IP address. f. Type the NTP system IP address and press Enter. g. If you indicated more than one IP address, the setup script prompts you to choose which nodes to use for each address. Note, are nodes (for example: 2 3 for nodes 2 and 3). Enter config for IP #0 IP Address: Netmask: Nodes Using IP address: h. Verify the IP address information is correct. Type y and press Enter. 16. The OOTB has completed when the following displays: Out-Of-The-Box has completed. Please continue with the SP moment of birth. Exiting Out-Of-The-Box Experience... Installing HP 3PAR OS Files After completing the Service Processor Setup wizard process, HP 3PAR OS files must first be installed onto the SP in order to communicate and add a storage system. To install the OS files: 1. Insert the HP 3PAR OS Release Distribution CD into the SP. 2. Log in to the SP as spvar (password prompted). 3. In the SPMaint main menu, type: • 1 for SP Control/Status • 16 for Maintain SP Software • 1 for Update SP Software Revision • 2 for CDROM to install the files. NOTE: The installation process takes approximately five minutes. 48 Installing Storage Software Manually

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
14.
Verify the correct license is displayed and press
Enter
. If the license information is not correct,
type
c
and press
Enter
to continue with the system setup. After completing the system setup,
contact your local service provider for technical support to obtain the proper license keys.
15.
Complete the network configuration:
a.
When prompted, type the number of IP addresses used by the system (usually 1) and
press
Enter
.
b.
Type the IP address and press
Enter
.
c.
Type the netmask and press
Enter
. When prompted, press
Enter
again to accept the
previously entered netmask.
d.
Type the gateway IP address and press
Enter
.
e.
Specify the speed and duplex and press
Enter
.
Please specify speed (10, 100 or 1000) and duplex (half or full), or auto to
use autonegotation: auto
NOTE:
If an NTP system IP address is not provided, use the SP IP address.
f.
Type the NTP system IP address and press
Enter
.
g.
If you indicated more than one IP address, the setup script prompts you to choose which
nodes to use for each address. Note,
<X Y Z>
are nodes (for example:
2 3
for nodes
2 and 3).
Enter config for IP #0
IP Address:
<IPaddress>
Netmask:
<netmask>
Nodes Using IP address:
<X Y Z>
h.
Verify the IP address information is correct. Type
y
and press
Enter
.
16.
The OOTB has completed when the following displays:
Out-Of-The-Box has completed.
Please continue with the SP moment of birth.
Exiting Out-Of-The-Box Experience...
Installing HP 3PAR OS Files
After completing the Service Processor Setup wizard process, HP 3PAR OS files must first be
installed onto the SP in order to communicate and add a storage system.
To install the OS files:
1.
Insert the HP 3PAR OS Release Distribution CD into the SP.
2.
Log in to the SP as
spvar
(password prompted).
3.
In the SPMaint main menu, type:
•
1
for
SP Control/Status
•
16
for
Maintain SP Software
•
1
for
Update SP Software Revision
•
2
for
CDROM
to install the files.
NOTE:
The installation process takes approximately five minutes.
48
Installing Storage Software Manually