HP 3PAR StoreServ 7450 2-node HP 3PAR StoreServ 7000 SmartStart 1.2 User&# - Page 10

For more information, see your completed Storage System Software Installation Checklist

Get HP 3PAR StoreServ 7450 2-node PDF manuals and user guides View all HP 3PAR StoreServ 7450 2-node manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

◦ The HP 3PAR storage system setup is verified, the storage system is powered on, and the LEDs are functioning correctly. ◦ Either the physical Service Processor is installed and powered on and you have assigned it an IP address, or the virtual Service Processor is installed and connected and you have determined the temporary IP address. • Make sure you have the following: ◦ Administrative access to the Windows host systems you are configuring If you are planning to configure a remote host system (a machine other than the machine into which you inserted the SmartStart media), you must be able to use the same ID and password to gain administrator access to both the system running SmartStart (the local host) and the remote host. ◦ Rights to configure storage To configure storage, your user account on the HP 3PAR storage system must either be assigned a Super user or Edit role or be granted the following rights: - host_create - vv_create - vlun_create ◦ The necessary Service Processor and HP 3PAR storage system information for initialization and configuration For more information, see your completed Storage System Software Installation Checklist from the HP 3PAR StoreServ 7000 Site Planning Manual. - Service Processor information - The Service Processor IP address, subnet mask, and gateway IP address For more information about determining the temporary IP address and assigning the permanent IP address, see the HP 3PAR StoreServ 7000 Storage Installation Guide. - Host name to assign - DNS settings (if applicable) - Proxy server settings (if applicable) - New password to assign to the user account for the two Storage System Setup wizards (setupusr) - New password to assign to the user account for the Service Processor (3parcust) NOTE: Passwords for the setupusr and 3parcust user accounts must be between 7 and 32 characters in length and can consist of alphanumeric characters and the following special characters: period (.), plus sign (+), dash (-), equals sign (=), and forward slash (/). - HP 3PAR StoreServ Storage system information - Storage system serial number This seven-digit number is located on the back of your HP 3PAR StoreServ Storage system next to the power switch for the node enclosure power cooling module (PCM1). It begins with "16" (for example, 1624635). For more information, see "Locating the Serial Number" (page 17). - Storage system name 10 Prepare to Configure

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
◦
The HP 3PAR storage system setup is verified, the storage system is powered on, and the
LEDs are functioning correctly.
◦
Either the physical Service Processor is installed and powered on and you have assigned
it an IP address, or the virtual Service Processor is installed and connected and you have
determined the temporary IP address.
•
Make sure you have the following:
Administrative access to the Windows host systems you are configuring
If you are planning to configure a remote host system (a machine other than the machine
into which you inserted the SmartStart media), you must be able to use the same ID and
◦
password to gain administrator access to both the system running SmartStart (the local
host) and the remote host.
◦
Rights to configure storage
To configure storage, your user account on the HP 3PAR storage system must either be
assigned a Super user or Edit role or be granted the following rights:
–
host_create
–
vv_create
–
vlun_create
◦
The necessary Service Processor and HP 3PAR storage system information for initialization
and configuration
For more information, see your completed Storage System Software Installation Checklist
from the
HP 3PAR StoreServ 7000 Site Planning Manual
.
–
Service Processor information
The Service Processor IP address, subnet mask, and gateway IP address
For more information about determining the temporary IP address and assigning
the permanent IP address, see the
HP 3PAR StoreServ 7000 Storage Installation
Guide
.
–
–
Host name to assign
–
DNS settings (if applicable)
–
Proxy server settings (if applicable)
–
New password to assign to the user account for the two Storage System Setup
wizards (
setupusr
)
–
New password to assign to the user account for the Service Processor (
3parcust
)
NOTE:
Passwords for the
setupusr
and
3parcust
user accounts must be between
7 and 32 characters in length and can consist of alphanumeric characters and
the following special characters: period (.), plus sign (+), dash (-), equals sign
(=), and forward slash (/).
–
HP 3PAR StoreServ Storage system information
–
Storage system serial number
This seven-digit number is located on the back of your HP 3PAR StoreServ Storage
system next to the power switch for the node enclosure power cooling module
(PCM1). It begins with “16” (for example, 1624635). For more information,
see
“Locating the Serial Number” (page 17)
.
–
Storage system name
10
Prepare to Configure