HP 3PAR StoreServ 7450 2-node HP 3PAR StoreServ 7000 SmartStart 1.2 User&# - Page 30

Con the iSCSI Target, Install and Start Host Explorer, Summary: iSCSI Host Configuration

Get HP 3PAR StoreServ 7450 2-node PDF manuals and user guides View all HP 3PAR StoreServ 7450 2-node manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Configure the iSCSI Target 1. Select the IP address of the iSCSI initiator on the host system. 2. Click Configure. 3. Click Next. Troubleshooting the iSCSI Connection If the iSCSI initiator on the host system cannot connect to the HP 3PAR StoreServ Storage system, verify your configuration: 1. Verify your IP settings: • IP address • Subnet mask • Gateway 2. Check your iSCSI connection. To do this, ping the HP 3PAR StoreServ Storage system from the host. Troubleshooting Task Completion If SmartStart displays the Failed to validate whether the current Windows task is complete message, click Configure again. If the problem persists, contact HP support. For more information, see "Support and Other Resources" (page 57). Install and Start Host Explorer Host Explorer helps you discover and manage host system paths. Installation is optional. If you do not install Host Explorer, you must manually manage host paths. For more information, see "The Host Explorer Software Agent" (page 44). To install HP 3PAR Host Explorer: 1. Click Install. 2. Click Next. Summary: iSCSI Host Configuration 1. Review your iSCSI setup. 2. Click Finish. Configuring Multiple iSCSI Ports To configure another iSCSI port: 1. Go to SmartStart wizard step 4, Configure hosts. 2. Click Configure iSCSI hosts. 3. In steps 1 through 4 of the iSCSI Host Configuration wizard, configure the same iSCSI host system. 4. At iSCSI Host Configuration wizard step 5, Configure the iSCSI port, select an additional port and configure it. 5. In the final steps of the iSCSI Host Configuration wizard, complete the iSCSI configuration for this host. 30 Configure the Hosts

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
Configure the iSCSI Target
1.
Select the IP address of the iSCSI initiator on the host system.
2.
Click
Configure
.
3.
Click
Next
.
Troubleshooting the iSCSI Connection
If the iSCSI initiator on the host system cannot connect to the HP 3PAR StoreServ Storage system,
verify your configuration:
1.
Verify your IP settings:
•
IP address
•
Subnet mask
•
Gateway
2.
Check your iSCSI connection. To do this, ping the HP 3PAR StoreServ Storage system from
the host.
Troubleshooting Task Completion
If SmartStart displays the
Failed to validate whether the current Windows task is complete
message,
click
Configure
again.
If the problem persists, contact HP support. For more information, see
“Support and Other Resources”
(page 57)
.
Install and Start Host Explorer
Host Explorer helps you discover and manage host system paths. Installation is optional. If you do
not install Host Explorer, you must manually manage host paths. For more information, see
“The
Host Explorer Software Agent” (page 44)
.
To install HP 3PAR Host Explorer:
1.
Click
Install
.
2.
Click
Next
.
Summary: iSCSI Host Configuration
1.
Review your iSCSI setup.
2.
Click
Finish
.
Configuring Multiple iSCSI Ports
To configure another iSCSI port:
1.
Go to SmartStart wizard step 4,
Configure hosts
.
2.
Click
Configure iSCSI hosts
.
3.
In steps 1 through 4 of the iSCSI Host Configuration wizard, configure the same iSCSI host
system.
4.
At iSCSI Host Configuration wizard step 5,
Configure the iSCSI port
, select an additional port
and configure it.
5.
In the final steps of the iSCSI Host Configuration wizard, complete the iSCSI configuration for
this host.
30
Configure the Hosts