HP 3PAR StoreServ 7450 2-node HP 3PAR StoreServ 7000 SmartStart 1.2 User&# - Page 17

Setting Up the HP 3PAR StoreServ Storage System, Locating the Serial Number

Get HP 3PAR StoreServ 7450 2-node PDF manuals and user guides View all HP 3PAR StoreServ 7450 2-node manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

3 Setting Up the HP 3PAR StoreServ Storage System Before you can configure the HP 3PAR StoreServ Storage system, you must initialize it. The Storage System Setup wizard verifies your HP 3PAR storage system configuration, initializes the storage system, and runs initialization tests on the storage system. To set up and configure the HP 3PAR storage system: 1. Verify that the Service Processor is on the same subnet of the network as the HP 3PAR StoreServ 7000 Storage system you are setting up. 2. Click the Set up the Storage System link in SmartStart wizard step 2, Set up systems. 3. Enter the permanent Service Processor IP address. For more information about Service Processor IP addresses, see the HP 3PAR StoreServ 7000 Storage Installation Guide. 4. Enter the user name setupusr. 5. Enter the password for setupusr that you created in the Service Processor Setup wizard. Troubleshooting Access If you cannot access the Storage System Setup wizard, collect the relevant log files and contact HP support. For more information, see "Troubleshooting System Setup" (page 20). Locating the Serial Number The serial number on your HP 3PAR StoreServ Storage system is the seven-digit number located on the back of the storage system next to the power switch for the node enclosure power cooling module (PCM1). It begins with "16" (for example, 1612345). Locating the Serial Number 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
3 Setting Up the HP 3PAR StoreServ Storage System
Before you can configure the HP 3PAR StoreServ Storage system, you must initialize it. The Storage
System Setup wizard verifies your HP 3PAR storage system configuration, initializes the storage
system, and runs initialization tests on the storage system.
To set up and configure the HP 3PAR storage system:
1.
Verify that the Service Processor is on the same subnet of the network as the HP 3PAR StoreServ
7000 Storage system you are setting up.
2.
Click the
Set up the Storage System
link in SmartStart wizard step 2,
Set up systems
.
3.
Enter the permanent Service Processor IP address. For more information about Service Processor
IP addresses, see the
HP 3PAR StoreServ 7000 Storage Installation Guide
.
4.
Enter the user name
setupusr
.
5.
Enter the password for setupusr that you created in the Service Processor Setup wizard.
Troubleshooting Access
If you cannot access the Storage System Setup wizard, collect the relevant log files and contact
HP support. For more information, see
“Troubleshooting System Setup” (page 20)
.
Locating the Serial Number
The serial number on your HP 3PAR StoreServ Storage system is the seven-digit number located
on the back of the storage system next to the power switch for the node enclosure power cooling
module (PCM1). It begins with “16” (for example, 1612345).
Locating the Serial Number
17