HP 3PAR StoreServ 7450 2-node HP 3PAR StoreServ 7000 SmartStart 1.2 User&# - Page 9

Prepare to Con Prerequisites

Get HP 3PAR StoreServ 7450 2-node PDF manuals and user guides View all HP 3PAR StoreServ 7450 2-node manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

1 Prepare to Configure Prerequisites IMPORTANT: Before using SmartStart to configure your system, you must complete the setup tasks detailed in the HP 3PAR StoreServ 7000 Storage Installation Guide. To access the HP 3PAR StoreServ 7000 Storage Installation Guide, go to the HP 3PAR StoreServ Storage site and click the Support link for your product: http://www.hp.com/go/3par A DHCP network is no longer required to set up a virtual Service Processor (VSP). For more information about how to manually set the VSP IP address when DHCP is not available, see the HP 3PAR StoreServ 7000 Storage Installation Guide. NOTE: The Service Processor and StoreServ storage system must be on the same subnet. Before you configure your new HP 3PAR StoreServ 7000 Storage system: • Verify that the following setup tasks are complete, as described in the HP 3PAR StoreServ 7000 Storage Installation Guide: ◦ All components are installed. ◦ If you are using a VSP, the system time is set to the correct time of day on the ESXi host. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
1 Prepare to Configure
Prerequisites
IMPORTANT:
Before using SmartStart to configure your system, you must complete the setup tasks
detailed in the
HP 3PAR StoreServ 7000 Storage Installation Guide
.
To access the
HP 3PAR StoreServ 7000 Storage Installation Guide
, go to the HP 3PAR StoreServ
Storage site and click the
Support
link for your product:
h
t
tp://w
w
w
.hp
.co
m/go/3par
A DHCP network is no longer required to set up a virtual Service Processor (
VSP
). For more
information about how to manually set the VSP IP address when DHCP is not available, see the
HP 3PAR StoreServ 7000 Storage Installation Guide
.
NOTE:
The
Service Processor
and StoreServ storage system must be on the same subnet.
Before you configure your new HP 3PAR StoreServ 7000 Storage system:
•
Verify that the following setup tasks are complete, as described in the
HP 3PAR StoreServ
7000 Storage Installation Guide
:
◦
All components are installed.
◦
If you are using a
VSP
, the system time is set to the correct time of day on the ESXi host.
9