Home » HP Manuals » Desktops » HP Dc7700 » Manual Viewer

HP Dc7700 vPro Setup and Configuration for the dc7700 Business PC with Intel v - Page 11

IP Address, Subnet Mask, Default Gateway Address, Enter, Preferred DNS Address, Alternate DNS

UPC - 882780715318

Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

c. Select IP Address, and then type a static address. Default Setting = 10.0.0.2, Recommended Setting = Network Dependent Example: 192.168.0.1 Make sure all AMT systems have a unique static IP address if more than one system is on the same network. Multiple systems sharing the same static IP address can lead to network collisions, which will cause the systems to not respond correctly. d. Select Subnet Mask, and then type a subnet mask. Default Setting = 255.255.255.0, Recommended Setting = Network Dependent Example: 255.255.255.0 e. Select Default Gateway Address, and then accept the default and press Enter. Default Setting = 0.0.0.0, Recommended Setting = Network Dependent, Leave as 0.0.0.0 if this option is not needed. f. Select Preferred DNS Address, and then accept the default value and press Enter. Default Setting = 0.0.0.0, Recommended Setting = Network Dependent Leave as 0.0.0.0 if this option is not needed. g. Select Alternate DNS Address, and then accept the default value and press Enter. Default Setting = 0.0.0.0, Recommended Setting = Network Dependent Leave as 0.0.0.0 if this option is not needed. h.Select Domain Name, and then type a domain name Default Setting = none, Recommended Setting = Network Dependent The domain name is blank by default. If not populated, then the default domain of "Provisionserver" is used when connecting to a Setup and Configuration Server. If the name of the S&CS is not "Provisionserver" and the domain name is blank, then an alias must be set up in the DHCP server to redirect the connection for "Provisionserver" to the proper S&CS domain name. If the Domain Name field is populated, that is the domain used. However, if there is no response after four DNS queries to the named domain, then that domain name is no longer used and the default "Provisionserver" is used. 17. Skip Provisioning Server. Default Setting = 0.0.0.0, Recommended Setting = Network Dependent This option is used in Enterprise mode when an Intel AMT Setup and Configuration (Provisioning) server is available. This option disappears once SMB mode is set in step 18. 11

Section	Page
vPro Setup and Configuration for the dc7700 Business PC with Intel vPro Technology	1
Introduction	2
AMT Setup and Configuration	2
AMT System Phases	2
SMB Mode - AMT Setup and Configuration with MEBx	3
Password Guidelines	3
BIOS Prerequisite	4
SMB Mode - AMT Setup and Configuration Steps	4
1. Press Ctrl-P during POST to enter Manageability Engine BIOS Extension (MEBx) Setup. You can dis play this option only during POST if set in F10-Setup.	4
Figure 1 Intel MEBx Password Screen	4
2. Type the default password, which is admin. Passwords are case-sensitive.	5
3. Change the MEBx password. The new password must meet the Strong Password criteria defined in the Password Guidelines Section. Type the password twice for verification.	5
4. Select the Intel ME Platform Configuration. A window displays indicating that the system resets after configuration.	5
5. Select Y. ME platform configuration allows IT personnel to configure ME features such as AMT/ASF selection, power options, firmware update capabilities, and so on.	5
Figure 2 Intel ME Platform Configuration screen	5
6. Select Intel ME State Control, and then select Enabled.	5
7. Select Intel ME Firmware Local Update Qualifier, and then select Always Open.	5
8. Skip LAN Controller.	6
9. Select Intel ME Features Control.	6
Figure 3 Intel ME Features Control Screen with AMT selected	7
10. Select Intel ME Power Control.	7
Figure 4 Intel ME Power Control Screen	7
11. Return to previous menu to exit the MEBx Setup and save AMT configuration. The system will display an Intel ME Configuration Complete message and reboot.	9
12. Press Ctrl-P during POST to enter MEBx Setup again.	9
13. Type the MEBx password.	9
14. Select Intel AMT Configuration.	10
Figure 5 Intel AMT Configuration screen	10
15. Select Host Name, and then type a host name.	10
16. Select TCP/IP.	10
17. Skip Provisioning Server.	11
18. Select Provision Model.	12
19. Skip Un-Provision. This option returns the system to factory defaults. See “Return to Default” on page 23 for more information about unprovisioning.	12
20. Skip VLAN.	12
21. Select SOL/IDE-R.	12
22. Select Remote Firmware Update, and then select Enabled.	12
23. Select Idle Timeout.	13
24. Select Return to previous menu.	13
25. Select Exit, and then select Y to exit the MEBx Setup and save settings.	13
Figure 6 Intel AMT Enabled and Configured - ME configuration complete	13
Intel AMT WebGUI	14
Connecting with the Intel AMT WebGUI - SMB Example	14
1. Power on an AMT system that has completed AMT Setup and Configuration.	14
2. Execute a Web browser from a separate system - a Management computer on the same subnet as the AMT computer.	14
3. Connect to the IP address specified in the MEBx and port of the AMT system.	14
4. Type the user name and password. The default username is admin and the password is what you set during AMT Setup in the MEBx.	15
Figure 7 Intel AMT WebGUI Screen	15
5. Review system information and/or make any necessary changes.	15
6. Select Exit.	15
Enterprise Mode Setup and Configuration	16
Enterprise Mode - AMT Setup and Configuration Steps	16
1. Access the MEBx by pressing Ctrl-P during POST.	16
2. Type the default password, which is admin.	16
3. Change the MEBx password, following strong password guidelines.	16
4. Select Intel ME Platform Configuration.	16
5. In Intel ME State Control, select Enabled.	16
6. In Intel ME Firmware Local Update Qualifier, select Always Open.	16
7. Skip LAN Controller.	16
8. Select Intel ME Features Control.	16
9. Select Intel ME Power Control.	16
10. Select Exit and save. The system displays the Intel ME Configuration Complete message, and then reboots.	16
11. Press Ctrl-P during POST to enter MEBx Setup again.	16
12. Type the MEBx password.	16
13. Select Intel AMT Configuration. The Intel AMT Configuration screen includes numerous options, which are available by scrolling down the menu.	17
Figure 8 Intel AMT Configuration Screen	17
Figure 9 Intel AMT Configuration Screen Continued	17
14. Select Host Name, and then type a host name	17
15. Select TCP/IP.	18
16. Select Provisioning Server.	18
17. Select Provision Model.	18
18. Select Set PID and PPS.	18
19. Skip Un-Provision. This option returns the system to factory defaults. See the Return to Default sec tion for more information about unprovisioning.	18
20. Skip VLAN.	19
21. Select SOL/IDE-R, and then select Y.	19
22. Select Remote Firmware Update, and then select Enabled.	19
23. Skip Set PRTC.	19
24. Select Idle Timeout.	19
25. Select Return to previous menu.	19
26. Select Exit, and then select Y to exit the MEBx Setup and save settings. The system displays an Intel ME Configuration Complete message and reboots.	20
27. Turn off the system and remove power. The system is now in In-Setup Mode and is ready for deploy ment.	20
28. Plug the system into a power source and connect the network. Use the integrated Intel 82566DM NIC. Intel AMT does not work with any other NIC solution.	20
Setup and Configuration Server Preparation	21
Provisioning Methods	21
Legacy	21
IT TLS-PSK	21
OEM TLS-PSK	22
Return to Default	23
Figure 10 Intel AMT Unprovisioning Screen	23
1. Select Un-Provision.	23
2. Select Return to previous menu.	23
3. Select Exit, and then select Y. The system reboots.	23
Full Return to Factory Defaults	24
USB Drive Key Set Up and Configuration	24
1. An IT technician inserts a USB drive key into a system with a management console.	24
2. The technician request local setup and configuration records from an S&CS through the console.	24
3. The S&CS:	24
4. The management console writes the password, PID, and PPS sets to a Setup.bin file in the USB drive key.	24
5. The technician takes the USB drive key to the staging area where new AMT platforms are located. The technician:	24
6. The system BIOS detects the USB drive key.	24
7. The system BIOS displays a message that automatic setup and configuration will occur.	25
8. MEBx processes the record.	25
9. MEBx writes a completion message to display.	25
10. The IT technician powers down the system. The system is now in In-Setup phase and is ready to be dis tributed to users in an Enterprise mode environment.	25
11. Repeat Step 5 if necessary (more than one system).	25
USB Drive Key Requirements	25
Appendix A: Frequently Asked Questions	26
Appendix B: Power / Sleep / Global States Explained	29

Match case Limit results 1 per page

c. Select

IP Address

, and then type a static address.

Default Setting = 10.0.0.2, Recommended Setting = Network Dependent

Example: 192.168.0.1

Make sure all AMT systems have a unique static IP address if more than one system is on the

same network. Multiple systems sharing the same static IP address can lead to network collisions,

which will cause the systems to not respond correctly.

d. Select

Subnet Mask

, and then type a subnet mask.

Default Setting = 255.255.255.0, Recommended Setting = Network Dependent

Example: 255.255.255.0

e. Select

Default Gateway Address

, and then accept the default and press

Enter

Default Setting = 0.0.0.0, Recommended Setting = Network Dependent,

Leave as 0.0.0.0 if this option is not needed.

f. Select

Preferred DNS Address

, and then accept the default value and press

Enter

Default Setting = 0.0.0.0, Recommended Setting = Network Dependent

Leave as 0.0.0.0 if this option is not needed.

g. Select

Alternate DNS Address

, and then accept the default value and press

Enter

Default Setting = 0.0.0.0, Recommended Setting = Network Dependent

Leave as 0.0.0.0 if this option is not needed.

h.Select

Domain Name

, and then type a domain name

Default Setting = none, Recommended Setting = Network Dependent

The domain name is blank by default. If not populated, then the default domain of

“Provisionserver” is used when connecting to a Setup and Configuration Server.

If the name of the S&CS is not “Provisionserver” and the domain name is blank, then an alias

must be set up in the DHCP server to redirect the connection for "Provisionserver" to the proper

S&CS domain name.

If the

Domain Name

field is populated, that is the domain used. However, if there is no

response after four DNS queries to the named domain, then that domain name is no longer

used

and the default “Provisionserver” is used.

17.

Skip

Provisioning Server

Default Setting = 0.0.0.0, Recommended Setting = Network Dependent

This option is used in Enterprise mode when an Intel AMT Setup and Configuration (Provisioning)

server is available. This option disappears once SMB mode is set in step 18.