Home » HP Manuals » Desktops » HP Dc7700 » Manual Viewer

HP Dc7700 vPro Setup and Configuration for the dc7700 Business PC with Intel v - Page 18

This option is for Provisioning ID PID and Provisioning Passphrase PPS entry. PIDs are 8 characters

UPC - 882780715318

Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

15. Select TCP/IP. a. Select Disabling Network Interface, and then select N. Default Setting = Network Interface Enabled, Recommended Setting = Network Interface Enabled If network is disabled, then all remote AMT capabilities are disabled and TCP/IP settings will not be necessary. This option is a toggle, and the next time you access it you are prompted with the opposite setting. b. Select DHCP Disable, and then select N. Default Setting = DHCP Enabled, Recommended Setting = User Dependent For the purpose of this white paper, DHCP is enabled. 16. Select Provisioning Server. a. Type the Provisioning Server IP. Default Setting = 0.0.0.0, Recommended Setting = Network Dependent b. Type the Port. Default Setting = 9971, Recommended Setting = S&CS Dependent This option is used in Enterprise mode when an Intel AMT Setup and Configuration (Provisioning) Server is available. It points to the IP address of the S&CS. If the IP and port are left as the default, the ME looks for ProvisionServer on DNS at port 9971. Some ISV's may require additional settings, such as the SC&S port number and SC&S IP address. Contact your Management Console ISV for more details. 17. Select Provision Model. a. Change to Intel AMT 1.0 Mode, and then select N. Default Setting = Intel AMT 2.0 Mode, Recommended Setting = Intel AMT 2.0 Mode b. Change to Small Business, and then select N. Default Setting = Enterprise, Recommended Setting = Enterprise c. Select Return to previous menu. 18. Select Set PID and PPS. Default Setting = None, Recommended Setting = System Dependent This option is for Provisioning ID (PID) and Provisioning Passphrase (PPS) entry. PIDs are 8 characters and PPS are 32 characters. There are dashes between every set of 4 characters, so including dashes, PIDs are 9 characters and PPS are 40 characters. An S&CS must generate these entries. The Admin Password, PID, and PPS can be pre-populated by HP during manufacturing. See the OEM TLS-PSK section for details. 19. Skip Un-Provision. This option returns the system to factory defaults. See the Return to Default section for more information about unprovisioning. 18

Section	Page
vPro Setup and Configuration for the dc7700 Business PC with Intel vPro Technology	1
Introduction	2
AMT Setup and Configuration	2
AMT System Phases	2
SMB Mode - AMT Setup and Configuration with MEBx	3
Password Guidelines	3
BIOS Prerequisite	4
SMB Mode - AMT Setup and Configuration Steps	4
1. Press Ctrl-P during POST to enter Manageability Engine BIOS Extension (MEBx) Setup. You can dis play this option only during POST if set in F10-Setup.	4
Figure 1 Intel MEBx Password Screen	4
2. Type the default password, which is admin. Passwords are case-sensitive.	5
3. Change the MEBx password. The new password must meet the Strong Password criteria defined in the Password Guidelines Section. Type the password twice for verification.	5
4. Select the Intel ME Platform Configuration. A window displays indicating that the system resets after configuration.	5
5. Select Y. ME platform configuration allows IT personnel to configure ME features such as AMT/ASF selection, power options, firmware update capabilities, and so on.	5
Figure 2 Intel ME Platform Configuration screen	5
6. Select Intel ME State Control, and then select Enabled.	5
7. Select Intel ME Firmware Local Update Qualifier, and then select Always Open.	5
8. Skip LAN Controller.	6
9. Select Intel ME Features Control.	6
Figure 3 Intel ME Features Control Screen with AMT selected	7
10. Select Intel ME Power Control.	7
Figure 4 Intel ME Power Control Screen	7
11. Return to previous menu to exit the MEBx Setup and save AMT configuration. The system will display an Intel ME Configuration Complete message and reboot.	9
12. Press Ctrl-P during POST to enter MEBx Setup again.	9
13. Type the MEBx password.	9
14. Select Intel AMT Configuration.	10
Figure 5 Intel AMT Configuration screen	10
15. Select Host Name, and then type a host name.	10
16. Select TCP/IP.	10
17. Skip Provisioning Server.	11
18. Select Provision Model.	12
19. Skip Un-Provision. This option returns the system to factory defaults. See “Return to Default” on page 23 for more information about unprovisioning.	12
20. Skip VLAN.	12
21. Select SOL/IDE-R.	12
22. Select Remote Firmware Update, and then select Enabled.	12
23. Select Idle Timeout.	13
24. Select Return to previous menu.	13
25. Select Exit, and then select Y to exit the MEBx Setup and save settings.	13
Figure 6 Intel AMT Enabled and Configured - ME configuration complete	13
Intel AMT WebGUI	14
Connecting with the Intel AMT WebGUI - SMB Example	14
1. Power on an AMT system that has completed AMT Setup and Configuration.	14
2. Execute a Web browser from a separate system - a Management computer on the same subnet as the AMT computer.	14
3. Connect to the IP address specified in the MEBx and port of the AMT system.	14
4. Type the user name and password. The default username is admin and the password is what you set during AMT Setup in the MEBx.	15
Figure 7 Intel AMT WebGUI Screen	15
5. Review system information and/or make any necessary changes.	15
6. Select Exit.	15
Enterprise Mode Setup and Configuration	16
Enterprise Mode - AMT Setup and Configuration Steps	16
1. Access the MEBx by pressing Ctrl-P during POST.	16
2. Type the default password, which is admin.	16
3. Change the MEBx password, following strong password guidelines.	16
4. Select Intel ME Platform Configuration.	16
5. In Intel ME State Control, select Enabled.	16
6. In Intel ME Firmware Local Update Qualifier, select Always Open.	16
7. Skip LAN Controller.	16
8. Select Intel ME Features Control.	16
9. Select Intel ME Power Control.	16
10. Select Exit and save. The system displays the Intel ME Configuration Complete message, and then reboots.	16
11. Press Ctrl-P during POST to enter MEBx Setup again.	16
12. Type the MEBx password.	16
13. Select Intel AMT Configuration. The Intel AMT Configuration screen includes numerous options, which are available by scrolling down the menu.	17
Figure 8 Intel AMT Configuration Screen	17
Figure 9 Intel AMT Configuration Screen Continued	17
14. Select Host Name, and then type a host name	17
15. Select TCP/IP.	18
16. Select Provisioning Server.	18
17. Select Provision Model.	18
18. Select Set PID and PPS.	18
19. Skip Un-Provision. This option returns the system to factory defaults. See the Return to Default sec tion for more information about unprovisioning.	18
20. Skip VLAN.	19
21. Select SOL/IDE-R, and then select Y.	19
22. Select Remote Firmware Update, and then select Enabled.	19
23. Skip Set PRTC.	19
24. Select Idle Timeout.	19
25. Select Return to previous menu.	19
26. Select Exit, and then select Y to exit the MEBx Setup and save settings. The system displays an Intel ME Configuration Complete message and reboots.	20
27. Turn off the system and remove power. The system is now in In-Setup Mode and is ready for deploy ment.	20
28. Plug the system into a power source and connect the network. Use the integrated Intel 82566DM NIC. Intel AMT does not work with any other NIC solution.	20
Setup and Configuration Server Preparation	21
Provisioning Methods	21
Legacy	21
IT TLS-PSK	21
OEM TLS-PSK	22
Return to Default	23
Figure 10 Intel AMT Unprovisioning Screen	23
1. Select Un-Provision.	23
2. Select Return to previous menu.	23
3. Select Exit, and then select Y. The system reboots.	23
Full Return to Factory Defaults	24
USB Drive Key Set Up and Configuration	24
1. An IT technician inserts a USB drive key into a system with a management console.	24
2. The technician request local setup and configuration records from an S&CS through the console.	24
3. The S&CS:	24
4. The management console writes the password, PID, and PPS sets to a Setup.bin file in the USB drive key.	24
5. The technician takes the USB drive key to the staging area where new AMT platforms are located. The technician:	24
6. The system BIOS detects the USB drive key.	24
7. The system BIOS displays a message that automatic setup and configuration will occur.	25
8. MEBx processes the record.	25
9. MEBx writes a completion message to display.	25
10. The IT technician powers down the system. The system is now in In-Setup phase and is ready to be dis tributed to users in an Enterprise mode environment.	25
11. Repeat Step 5 if necessary (more than one system).	25
USB Drive Key Requirements	25
Appendix A: Frequently Asked Questions	26
Appendix B: Power / Sleep / Global States Explained	29

Match case Limit results 1 per page

15.

Select

TCP/IP

a. Select

Disabling Network Interface

, and then select

Default Setting = Network Interface Enabled, Recommended Setting = Network Interface

Enabled

If network is disabled, then all remote AMT capabilities are disabled and TCP/IP settings will not

be necessary. This option is a toggle, and the next time you access it you are prompted with the

opposite setting.

b. Select

DHCP Disable

, and then select

Default Setting = DHCP Enabled, Recommended Setting = User Dependent

For the purpose of this white paper, DHCP is enabled.

16.

Select

Provisioning Server

a. Type the

Provisioning Server IP

Default Setting = 0.0.0.0, Recommended Setting = Network Dependent

b. Type the

Port

Default Setting = 9971, Recommended Setting = S&CS Dependent

This option is used in Enterprise mode when an Intel AMT Setup and Configuration (Provisioning)

Server is available. It points to the IP address of the S&CS.

If the IP and port are left as the default, the ME looks for

ProvisionServer

on DNS at port

9971.

Some ISV’s may require additional settings, such as the SC&S port number and SC&S IP

address.

Contact your Management Console ISV for more details.

17.

Select

Provision Model

a. Change to

Intel AMT 1.0 Mode,

and then select

Default Setting = Intel AMT 2.0 Mode, Recommended Setting = Intel AMT 2.0 Mode

b. Change to

Small Business,

and then select

Default Setting = Enterprise, Recommended Setting = Enterprise

c. Select

Return to previous menu

18.

Select

Set PID and PPS

Default Setting = None, Recommended Setting = System Dependent

This option is for Provisioning ID (PID) and Provisioning Passphrase (PPS) entry. PIDs are 8 characters

and PPS are 32 characters. There are dashes between every set of 4 characters, so including dashes,

PIDs are 9 characters and PPS are 40 characters. An S&CS must generate these entries.

The Admin Password, PID, and PPS can be pre-populated by HP during manufacturing. See the OEM

TLS-PSK section for details.

19.

Skip

Un-Provision

. This option returns the system to factory defaults. See the Return to Default sec-

tion for more information about unprovisioning.