Home » HP Manuals » Desktops » HP Dc7700 » Manual Viewer

HP Dc7700 vPro Setup and Configuration for the dc7700 Business PC with Intel v - Page 19

Appendix C: Wake-On-ME Explained

UPC - 882780715318

Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

20. Skip VLAN. Default Setting = Disabled, Recommended Setting = User Dependent This option enables or disables VLAN support. If VLAN is enabled, then the VLAN tag must be provided (1-4094). 21. Select SOL/IDE-R, and then select Y. a. A message window indicates that the system resets after configuration. b. Select Username and Password, and then select Enabled. Default Setting = Enabled, Recommended Setting = Enabled This option allows you to add users and passwords from the WebGUI. If the option is disabled, then only the administrator has MEBx remote access. c. Select Serial Over LAN, and then select Enabled. Default Setting = Enabled, Recommended Setting = Enabled d. Select IDE Redirection, and then select Enabled. Default Setting = Enabled, Recommended Setting = Enabled 22. Select Remote Firmware Update, and then select Enabled. Default Setting = Enabled, Recommended Setting = Enabled This option enables or disables the ability to remotely update the ME firmware. 23. Skip Set PRTC. Default Setting = None, Recommended Setting = Current Date and Time This option sets the PRTC (Protected Real Time Clock). It is used with TLS mutual authentication, which checks for the client certificate for expiration based on its PRTC. PRTC has a valid date range of 1/1/ 2004 to 1/4/2021. 24. Select Idle Timeout. Default Setting = 0x1, Recommended Setting = 0x1 This option sets the timeout value for Wake-On-ME. The default timeout value is 0x1 from the factory, but 0x0 if CMOS is cleared. A value of 0x0 means the Wake-On-ME feature is disabled and the ME will not go to sleep when not being used in a nonactive system. HP recommends a setting of 0x1, which allows the ME to go to sleep after 1 minute of inactivity. The timeout value can be set in both decimal and hexadecimal notation and is in units of minutes. It must be set to a non-zero value for the ME to take advantage of Wake-On-ME. Hexadecimal settings are preceded by a "0x", so one minute is "0x1". This value is not used when the system is in an active state - S0. This value is used only if the ME On in Host Sleep State setting is set to Always. See "Appendix C: Wake-On-ME Explained" on page 30 for an explanation of Wake-On-ME. 25. Select Return to previous menu. 19

Section	Page
vPro Setup and Configuration for the dc7700 Business PC with Intel vPro Technology	1
Introduction	2
AMT Setup and Configuration	2
AMT System Phases	2
SMB Mode - AMT Setup and Configuration with MEBx	3
Password Guidelines	3
BIOS Prerequisite	4
SMB Mode - AMT Setup and Configuration Steps	4
1. Press Ctrl-P during POST to enter Manageability Engine BIOS Extension (MEBx) Setup. You can dis play this option only during POST if set in F10-Setup.	4
Figure 1 Intel MEBx Password Screen	4
2. Type the default password, which is admin. Passwords are case-sensitive.	5
3. Change the MEBx password. The new password must meet the Strong Password criteria defined in the Password Guidelines Section. Type the password twice for verification.	5
4. Select the Intel ME Platform Configuration. A window displays indicating that the system resets after configuration.	5
5. Select Y. ME platform configuration allows IT personnel to configure ME features such as AMT/ASF selection, power options, firmware update capabilities, and so on.	5
Figure 2 Intel ME Platform Configuration screen	5
6. Select Intel ME State Control, and then select Enabled.	5
7. Select Intel ME Firmware Local Update Qualifier, and then select Always Open.	5
8. Skip LAN Controller.	6
9. Select Intel ME Features Control.	6
Figure 3 Intel ME Features Control Screen with AMT selected	7
10. Select Intel ME Power Control.	7
Figure 4 Intel ME Power Control Screen	7
11. Return to previous menu to exit the MEBx Setup and save AMT configuration. The system will display an Intel ME Configuration Complete message and reboot.	9
12. Press Ctrl-P during POST to enter MEBx Setup again.	9
13. Type the MEBx password.	9
14. Select Intel AMT Configuration.	10
Figure 5 Intel AMT Configuration screen	10
15. Select Host Name, and then type a host name.	10
16. Select TCP/IP.	10
17. Skip Provisioning Server.	11
18. Select Provision Model.	12
19. Skip Un-Provision. This option returns the system to factory defaults. See “Return to Default” on page 23 for more information about unprovisioning.	12
20. Skip VLAN.	12
21. Select SOL/IDE-R.	12
22. Select Remote Firmware Update, and then select Enabled.	12
23. Select Idle Timeout.	13
24. Select Return to previous menu.	13
25. Select Exit, and then select Y to exit the MEBx Setup and save settings.	13
Figure 6 Intel AMT Enabled and Configured - ME configuration complete	13
Intel AMT WebGUI	14
Connecting with the Intel AMT WebGUI - SMB Example	14
1. Power on an AMT system that has completed AMT Setup and Configuration.	14
2. Execute a Web browser from a separate system - a Management computer on the same subnet as the AMT computer.	14
3. Connect to the IP address specified in the MEBx and port of the AMT system.	14
4. Type the user name and password. The default username is admin and the password is what you set during AMT Setup in the MEBx.	15
Figure 7 Intel AMT WebGUI Screen	15
5. Review system information and/or make any necessary changes.	15
6. Select Exit.	15
Enterprise Mode Setup and Configuration	16
Enterprise Mode - AMT Setup and Configuration Steps	16
1. Access the MEBx by pressing Ctrl-P during POST.	16
2. Type the default password, which is admin.	16
3. Change the MEBx password, following strong password guidelines.	16
4. Select Intel ME Platform Configuration.	16
5. In Intel ME State Control, select Enabled.	16
6. In Intel ME Firmware Local Update Qualifier, select Always Open.	16
7. Skip LAN Controller.	16
8. Select Intel ME Features Control.	16
9. Select Intel ME Power Control.	16
10. Select Exit and save. The system displays the Intel ME Configuration Complete message, and then reboots.	16
11. Press Ctrl-P during POST to enter MEBx Setup again.	16
12. Type the MEBx password.	16
13. Select Intel AMT Configuration. The Intel AMT Configuration screen includes numerous options, which are available by scrolling down the menu.	17
Figure 8 Intel AMT Configuration Screen	17
Figure 9 Intel AMT Configuration Screen Continued	17
14. Select Host Name, and then type a host name	17
15. Select TCP/IP.	18
16. Select Provisioning Server.	18
17. Select Provision Model.	18
18. Select Set PID and PPS.	18
19. Skip Un-Provision. This option returns the system to factory defaults. See the Return to Default sec tion for more information about unprovisioning.	18
20. Skip VLAN.	19
21. Select SOL/IDE-R, and then select Y.	19
22. Select Remote Firmware Update, and then select Enabled.	19
23. Skip Set PRTC.	19
24. Select Idle Timeout.	19
25. Select Return to previous menu.	19
26. Select Exit, and then select Y to exit the MEBx Setup and save settings. The system displays an Intel ME Configuration Complete message and reboots.	20
27. Turn off the system and remove power. The system is now in In-Setup Mode and is ready for deploy ment.	20
28. Plug the system into a power source and connect the network. Use the integrated Intel 82566DM NIC. Intel AMT does not work with any other NIC solution.	20
Setup and Configuration Server Preparation	21
Provisioning Methods	21
Legacy	21
IT TLS-PSK	21
OEM TLS-PSK	22
Return to Default	23
Figure 10 Intel AMT Unprovisioning Screen	23
1. Select Un-Provision.	23
2. Select Return to previous menu.	23
3. Select Exit, and then select Y. The system reboots.	23
Full Return to Factory Defaults	24
USB Drive Key Set Up and Configuration	24
1. An IT technician inserts a USB drive key into a system with a management console.	24
2. The technician request local setup and configuration records from an S&CS through the console.	24
3. The S&CS:	24
4. The management console writes the password, PID, and PPS sets to a Setup.bin file in the USB drive key.	24
5. The technician takes the USB drive key to the staging area where new AMT platforms are located. The technician:	24
6. The system BIOS detects the USB drive key.	24
7. The system BIOS displays a message that automatic setup and configuration will occur.	25
8. MEBx processes the record.	25
9. MEBx writes a completion message to display.	25
10. The IT technician powers down the system. The system is now in In-Setup phase and is ready to be dis tributed to users in an Enterprise mode environment.	25
11. Repeat Step 5 if necessary (more than one system).	25
USB Drive Key Requirements	25
Appendix A: Frequently Asked Questions	26
Appendix B: Power / Sleep / Global States Explained	29

Match case Limit results 1 per page

20.

Skip VLAN

Default Setting = Disabled, Recommended Setting = User Dependent

This option enables or disables VLAN support. If VLAN is enabled, then the VLAN tag must be

provided (1-4094).

21.

Select

SOL/IDE-R

, and then select

a. A message window indicates that the system resets after configuration.

b. Select

Username and Password

, and then select

Enabled

Default Setting = Enabled, Recommended Setting = Enabled

This option allows you to add users and passwords from the WebGUI. If the option is disabled,

then only the administrator has MEBx remote access.

c. Select

Serial Over LAN

, and then select

Enabled

Default Setting = Enabled, Recommended Setting = Enabled

d. Select

IDE Redirection

, and then select

Enabled

Default Setting = Enabled, Recommended Setting = Enabled

22.

Select

Remote Firmware Update

, and then select

Enabled

Default Setting = Enabled, Recommended Setting = Enabled

This option enables or disables the ability to remotely update the ME firmware.

23.

Skip

Set PRTC

Default Setting = None, Recommended Setting = Current Date and Time

This option sets the PRTC (Protected Real Time Clock). It is used with TLS mutual authentication, which

checks for the client certificate for expiration based on its PRTC. PRTC has a valid date range of 1/1/

2004 to 1/4/2021.

24.

Select

Idle Timeout.

Default Setting = 0x1, Recommended Setting = 0x1

This option sets the timeout value for Wake-On-ME.

The default timeout value is 0x1 from the factory, but 0x0 if CMOS is cleared. A value of 0x0 means

the Wake-On-ME feature is disabled and the ME will not go to sleep when not being used in a non-

active system. HP recommends a setting of 0x1, which allows the ME to go to sleep after 1 minute of

inactivity.

The timeout value can be set in both decimal and hexadecimal notation and is in units of minutes. It

must be set to a non-zero value for the ME to take advantage of Wake-On-ME. Hexadecimal settings

are preceded by a “0x”, so one minute is “0x1”.

This value is not used when the system is in an active state - S0.

This value is used only if the

ME On in Host Sleep State

setting is set to

Always

See

“Appendix C: Wake-On-ME Explained” on page 30

for an explanation of Wake-On-ME.

25.

Select

Return to previous menu