HP Integrity Superdome 2 16-socket HP Integrity Superdome 2 User Service Guide - Page 35

Dynamic Power, Enabled, Disabled, OA1 IP Addr, Enclosure Name, Clear, Rack Name, DVD Drive

Get HP Integrity Superdome 2 16-socket PDF manuals and user guides View all HP Integrity Superdome 2 16-socket manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

NOTE: When calculating the Power Limit Watts ac value, derate the circuit to 80% of the maximum to prevent tripping the circuit breaker (United States only). NOTE: If your facility cannot support the calculated peak Watts ac, set the Power Watts ac value to match the capability of your facility. • Dynamic Power -The default setting is Enabled. The following selections are valid: ◦ Enabled -Some of the power supplies can be automatically placed on standby to increase overall enclosure power subsystem efficiency. ◦ Disabled -All power supplies share the load; the power subsystem efficiency varies based on load. • OA1 IP Addr- The default setting is DHCP; if no IP address is received, the IP address is 0.0.0.0. The IP address, mask, and gateway are set within this option. • OA2 IP Addr- If this module is present, the default setting is DHCP; if no IP address is received, the IP address is 0.0.0.0. If only one Onboard Administrator module is installed, then the screen displays "Not Present". • Enclosure Name- The default setting is a unique factory-assigned name. The accepted character values are 0-9, A-Z ,a-z, -, _, and the box character. The box character is used to signal the end of the name. NOTE: Do not use the box character in the middle of a text box. Entries in text boxes are truncated to the last character before the box character. TIP: Select Clear from the navigation bar to quickly clear entries in text boxes up to the symbol. • Rack Name - The default setting is UnnamedRack. The accepted character values are 0-9, A-Z, a-z, -, _, and the box character. The box character is used to signal the end of the name. • DVD Drive- The DVD connection Settings screen is a table of all the servers with the status of DVD Connection and blade name for that blade. Running the Insight Display installation 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
NOTE:
When calculating the Power Limit Watts ac value, derate the circuit to 80% of
the maximum to prevent tripping the circuit breaker (United States only).
NOTE:
If your facility cannot support the calculated peak Watts ac, set the Power Watts
ac value to match the capability of your facility.
•
Dynamic Power
—The default setting is Enabled. The following selections are valid:
Enabled
—Some of the power supplies can be automatically placed on standby to
increase overall enclosure power subsystem efficiency.
◦
◦
Disabled
—All power supplies share the load; the power subsystem efficiency varies
based on load.
•
OA1 IP Addr
— The default setting is DHCP; if no IP address is received, the IP address
is 0.0.0.0. The IP address, mask, and gateway are set within this option.
•
OA2 IP Addr
— If this module is present, the default setting is DHCP; if no IP address is
received, the IP address is 0.0.0.0. If only one Onboard Administrator module is installed,
then the screen displays “Not Present”.
•
Enclosure Name
— The default setting is a unique factory-assigned name. The accepted
character values are 0-9, A-Z ,a-z, -, _, and the box character. The box character is used
to signal the end of the name.
NOTE:
Do not use the box character in the middle of a text box. Entries in text boxes
are truncated to the last character before the box character.
TIP:
Select
Clear
from the navigation bar to quickly clear entries in text boxes up to the
symbol.
•
Rack Name
— The default setting is UnnamedRack. The accepted character values are
0-9, A-Z, a-z, -, _, and the box character. The box character is used to signal the end of
the name.
•
DVD Drive
— The DVD connection Settings screen is a table of all the servers with the
status of DVD Connection and blade name for that blade.
Running the Insight Display installation
35