HP Pro Tower 200 G9 Desktop PC Maintenance and Service Guide - Page 25

Memory modules (DIMMs

Get HP Pro Tower 200 G9 Desktop PC PDF manuals and user guides View all HP Pro Tower 200 G9 Desktop PC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

▲ Loosen the captive screw on the rear of the computer (1), slide the access panel back, and then lift it off the computer (2). To install the access panel, reverse the removal procedure. Memory modules (DIMMs) To remove the memory modules, use the information in this section. For a list of available memory modules, see Computer major components on page 4. The memory sockets on the system board are populated with at least one preinstalled memory module. To achieve the maximum memory support, you can populate the system board with up to 64 GB of memory configured in a high-performing dual-channel mode. For proper system operation, the DIMMs must adhere to the following specifications: ● Industry-standard 288-pin ● 1.2 volt DDR4-SDRAM memory modules ● DDR4-3200 SDRAM UDIMM ● Mandatory JEDEC SPD information The computer supports the following setups: ● 512 Mbit, 1 Gbit, 2 Gbit, and 4 Gbit non-ECC memory technologies ● Single-sided and double-sided memory modules 18 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
▲
Loosen the captive screw on the rear of the computer
(1)
, slide the access panel back, and then lift it off
the computer
(2)
.
To install the access panel, reverse the removal procedure.
Memory modules (DIMMs)
To remove the memory modules, use the information in this section.
For a list of available memory modules, see
Computer major components
on page
4
.
The memory sockets on the system board are populated with at least one preinstalled memory module. To
achieve the maximum memory support, you can populate the system board with up to 64 GB of memory
configured in a high-performing dual-channel mode.
For proper system operation, the DIMMs must adhere to the following specifications:
●
Industry-standard 288-pin
●
1.2 volt DDR4-SDRAM memory modules
●
DDR4-3200 SDRAM UDIMM
●
Mandatory JEDEC SPD information
The computer supports the following setups:
●
512 Mbit, 1 Gbit, 2 Gbit, and 4 Gbit non-ECC memory technologies
●
Single-sided and double-sided memory modules
18
Chapter 4
Removal and replacement procedures