HP StorageWorks 8/80 HP StorageWorks Fabric OS 6.2.0g release notes (5697-0355 - Page 34

Fabric OS 6.2.0 fixes, Table 8 Fabric OS 6.2.0 closed defects

Get HP StorageWorks 8/80 - SAN Switch PDF manuals and user guides View all HP StorageWorks 8/80 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Fabric OS 6.2.0 fixes The following table lists defects closed in the Fabric OS 6.2.0 firmware release. Table 8 Fabric OS 6.2.0 closed defects Closed defect summary Add Member button is disabled while creating a new TI Zone when the switch is in VF mode. Solution Fixed in Fabric OS 6.2.0. Workaround prior to upgrade: Add Other Port button can be used to add ports. This is available in the ADD TI Zone window. Under stress testing, cfgsave takes a long time and fails to propagate on 64 VE-VE FCIP tunnel 33 switch core-edge topology running I/O. Fixed in Fabric OS 6.2.0. Workaround prior to upgrade: Wait until fabric is not saturated to push configs around. Adding a B-series switch with conflicting domain ID into an EOS fabric may cause another switch to segment. Fixed in Fabric OS 6.2.0. Workaround prior to upgrade: Check the domain ID before adding a switch to any fabric. USB port LED of HP StorageWorks DC SAN Backbone Director CP blade stays ON after HA failover. CUP Port stuck in Contingent Allegiance State after z9 Host IPL. Spinfab and porttest (diagnostics) are not supported on ICL ports. Fixed in Fabric OS 6.2.0. Fixed in Fabric OS 6.2.0. Fixed in Fabric OS 6.2.0. Bogus core_file created and transferred after the first reboot after a firmwaredownload. Fixed in Fabric OS 6.2.0. B-series Multi-protocol (MP) Router blades in HP StorageWorks DC SAN Backbone Director chassis may fail sysverification tests. Fixed in Fabric OS 6.2.0. Workaround prior to upgrade: Rerun system verification. With a switch in Interop Mode 2 or 3, the Zoning configuration is not being included in configupload. Fixed in Fabric OS 6.2.0. FICON Channel continuously sends RRQ frames for approximately 20 seconds before aborting. Fixed in Fabric OS 6.2.0. If QoS and Diff Serv are enabled, some FCIP tunnels may not come online in the case of an 8 to 1 fan-in scenario. Fixed in Fabric OS 6.2.0. Workaround prior to upgrade: Port disable/enable the VE-Port Under rare conditions, fabric mode TopTalker monitor does not display correct flow values. Fixed in Fabric OS 6.2.0. Attempting to configure port mirroring on a director with both 4Gb and 8Gb blades may result in a software Verify error. Fixed in Fabric OS 6.2.0. 34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
Fabric OS 6.2.0 fixes
The following table lists defects closed in the Fabric OS 6.2.0 firmware release.
Table 8 Fabric OS 6.2.0 closed defects
Solution
Closed defect summary
Fixed in Fabric OS 6.2.0.
Workaround prior to upgrade:
Add Other Port
button can be used to
add ports. This is available in the
ADD TI Zone window.
Add Member button is disabled while creating a new TI Zone when
the switch is in VF mode.
Fixed in Fabric OS 6.2.0.
Workaround prior to upgrade:
Wait until fabric is not saturated to
push configs around.
Under stress testing,
cfgsave
takes a long time and fails to propagate
on 64 VE-VE FCIP tunnel 33 switch core-edge topology running I/O.
Fixed in Fabric OS 6.2.0.
Workaround prior to upgrade:
Check the domain ID before adding
a switch to any fabric.
Adding a B-series switch with conflicting domain ID into an EOS fabric
may cause another switch to segment.
Fixed in Fabric OS 6.2.0.
USB port LED of HP StorageWorks DC SAN Backbone Director CP
blade stays ON after HA failover.
Fixed in Fabric OS 6.2.0.
CUP Port stuck in Contingent Allegiance State after z9 Host IPL.
Fixed in Fabric OS 6.2.0.
Spinfab and porttest (diagnostics) are not supported on ICL ports.
Fixed in Fabric OS 6.2.0.
Bogus core_file created and transferred after the first reboot after a
firmwaredownload
.
Fixed in Fabric OS 6.2.0.
Workaround prior to upgrade:
Rerun system verification.
B-series Multi-protocol (MP) Router blades in HP StorageWorks DC
SAN Backbone Director chassis may fail
sysverification
tests.
Fixed in Fabric OS 6.2.0.
With a switch in Interop Mode 2 or 3, the Zoning configuration is not
being included in
configupload
.
Fixed in Fabric OS 6.2.0.
FICON Channel continuously sends RRQ frames for approximately 20
seconds before aborting.
Fixed in Fabric OS 6.2.0.
Workaround prior to upgrade:
Port disable/enable the VE-Port
If QoS and Diff Serv are enabled, some FCIP tunnels may not come
online in the case of an 8 to 1 fan-in scenario.
Fixed in Fabric OS 6.2.0.
Under rare conditions, fabric mode TopTalker monitor does not display
correct flow values.
Fixed in Fabric OS 6.2.0.
Attempting to configure port mirroring on a director with both 4Gb
and 8Gb blades may result in a software Verify error.
34