HP StorageWorks 8/80 HP StorageWorks Fabric OS 6.2.0g release notes (5697-0355 - Page 39

F_Ports on HP StorageWorks 8/8 and 8/24 SAN Switches AG cannot - 24 san switch console

Get HP StorageWorks 8/80 - SAN Switch PDF manuals and user guides View all HP StorageWorks 8/80 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Under Port Base Routing, topologyshow always shows None for the In Port field on HP StorageWorks 8/8, 8/24, and 8/40 SAN Switches. Fixed in Fabric OS 6.2.0. Workaround prior to upgrade: Use urouteshow to view the 'Out Port' selected for a particular 'In Port' to a domain when using Port Based Routing. HCL on switch continues if sent Pause frame is rejected by attached M-EOS switch. HCL on switch will sometimes continue, even when a sent Pause frame is rejected by another switch in the fabric. Fixed in Fabric OS 6.2.0. N_Port on Edge_AG_200E_PG got disabled with reason code Initiator/target connected to N-Port. Fixed in Fabric OS 6.2.0. Firmware download of Fabric OS 6.1.0 is allowed on an embedded blade that should not allow it. Fixed in Fabric OS 6.2.0. Fabric Rebuild during HP StorageWorks 8/40 SAN Switch HCL when 1 of 2 Backbones connect to a M6140 director. Fixed in Fabric OS 6.2.0. If Turboramtest is performed, the Telnet console will disconnect. Fixed in Fabric OS 6.2.0. Incorrect error when changed switchname for more than 24 characters through CLI in FMS mode. Fixed in Fabric OS 6.2.0. F_Ports on HP StorageWorks 8/8 and 8/24 SAN Switches AG cannot login, and become G_Ports. Fixed in Fabric OS 6.2.0. Occasionally an LD port gets into a lock up state that causes portGetVCCredits get failed and the ISL segments with LD incomp, although portcfgshow shows both sides of ISL config are the same. Fixed in Fabric OS 6.2.0. Workaround prior to upgrade: Reset with portcfgdefault/portcfgqos. EE monitor counters may not get updated after performing switchdisable/switchenble or reboot. Fixed in Fabric OS 6.2.0. Workaround prior to upgrade: Retrieve all EE monitors from the FLASH by issuing perfcfgrestore. All EE monitor counters will be properly updated. Static routing does not affect dynamic routes with DLS ON on supported platforms. Fixed in Fabric OS 6.2.0. The gzoneinfo.htm page returns empty data when CLI actually shows defined/eff cfg zone info for fabric. Fixed in Fabric OS 6.2.0. Workaround prior to upgrade: Do any other HTTP post operation from DCFM and then you see both the old data and the newly pushed zone info. Rebooting the switch sometimes helps. Third-party storage center application does not survive in an FCIP network with 1% packet loss and 100 ms network latency. Fixed in Fabric OS 6.2.0. Traffic Isolation failover policy reverts back to disabled from enabled after changing the port membership list. Fixed in Fabric OS 6.2.0. HP StorageWorks Fabric OS 6.2.0g release notes 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
Fixed in Fabric OS 6.2.0.
Workaround prior to upgrade:
Use
urouteshow
to view the 'Out
Port' selected for a particular 'In Port'
to a domain when using Port Based
Routing.
Under Port Base Routing,
topologyshow
always shows
None
for the
In Port field on HP StorageWorks 8/8, 8/24, and 8/40 SAN Switches.
Fixed in Fabric OS 6.2.0.
HCL on switch continues if sent Pause frame is rejected by attached
M-EOS switch. HCL on switch will sometimes continue, even when a
sent Pause frame is rejected by another switch in the fabric.
Fixed in Fabric OS 6.2.0.
N_Port on Edge_AG_200E_PG got disabled with reason code
Initi-
ator/target connected to N-Port
.
Fixed in Fabric OS 6.2.0.
Firmware download of Fabric OS 6.1.0 is allowed on an embedded
blade that should not allow it.
Fixed in Fabric OS 6.2.0.
Fabric Rebuild during HP StorageWorks 8/40 SAN Switch HCL when
1 of 2 Backbones connect to a M6140 director.
Fixed in Fabric OS 6.2.0.
If Turboramtest is performed, the Telnet console will disconnect.
Fixed in Fabric OS 6.2.0.
Incorrect error when changed
switchname
for more than 24 charac-
ters through CLI in FMS mode.
Fixed in Fabric OS 6.2.0.
F_Ports on HP StorageWorks 8/8 and 8/24 SAN Switches AG cannot
login, and become G_Ports.
Fixed in Fabric OS 6.2.0.
Workaround prior to upgrade:
Reset with
portcfgdefault
/
port-
cfgqos
.
Occasionally an LD port gets into a lock up state that causes
port-
GetVCCredits get failed
and the ISL segments with LD incomp,
although
portcfgshow
shows both sides of ISL config are the same.
Fixed in Fabric OS 6.2.0.
Workaround prior to upgrade:
Retrieve all EE monitors from the
FLASH by issuing
perfcfgrestore
.
All EE monitor counters will be prop-
erly updated.
EE monitor counters may not get updated after performing
switch-
disable
/
switchenble
or reboot.
Fixed in Fabric OS 6.2.0.
Static routing does not affect dynamic routes with DLS ON on supported
platforms.
Fixed in Fabric OS 6.2.0.
Workaround prior to upgrade:
Do any other HTTP post operation
from DCFM and then you see both
the old data and the newly pushed
zone info. Rebooting the switch
sometimes helps.
The
gzoneinfo.htm
page returns empty data when CLI actually
shows defined/eff cfg zone info for fabric.
Fixed in Fabric OS 6.2.0.
Third-party storage center application does not survive in an FCIP
network with 1% packet loss and 100 ms network latency.
Fixed in Fabric OS 6.2.0.
Traffic Isolation failover policy reverts back to disabled from enabled
after changing the port membership list.
HP StorageWorks Fabric OS 6.2.0g release notes
39