Honeywell HW5500E Owners Manual - Page 13

Step 1: Install Support Legs - hw5500el manual

Get Honeywell HW5500E - Portable Generator NOT PDF manuals and user guides
UPC - 894190002025
View all Honeywell HW5500E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Step 1: Install Support Legs To install support legs, you will need: ‰ M8 x 30 mm long hex flange bolts (2) ‰ M8 x 16 mm OD x 1.5 mm washers (2) ‰ M8 serrated flange nuts (6) ‰ M8 x 16 mm long full-thread hex flange bolts (4) ‰ Brackets (2) ‰ Rubber stoppers (2) ‰ Socket wrench with 13 mm socket* * Not included CAUTION Generator must be empty of engine oil and fuel. Drain engine oil and fuel, if necessary. Assembly 5. Attach a rubber stopper to the bottom of each support leg using a 30 mm long hex flange bolt and a serrated flange nut; tighten until securely seated. FIGURE 6: Rubber Stopper Attached to Support Leg 6. Attach each support leg to pre-drilled holes on bottom of generator frame, using 16 mm long full-thread hex flange bolts and serrated flange nuts; tighten until securely seated. Generator is heavy! Lifting generator can cause back or other bodily injury. NEVER lift generator without assistance. 1. Place the generator on a flat, level surface. 2. Stand at side of generator opposite recoil starter handle. Grip frame; carefully pull up and push to tilt generator backward. FIGURE 7: Support Leg Attached to Generator FIGURE 5: Tip onto Generator Recoil Side 3. Gently set generator onto the recoil side or elevate the generator by placing solid wood pieces underneath unit. 4. Place a washer in the center of each rubber stopper. HW5500/HW5500E/HW5500EL/HW5500L Portable Electrical Generator Owner's Manual www.honeywellgenerators.com 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
HW5500/HW5500E/HW5500EL/HW5500L Portable Electrical Generator Owner’s Manual
www.honeywellgenerators.com
7
Assembly
Step 1: Install Support Legs
1.
Place the generator on a flat, level surface.
2.
Stand at side of generator
opposite
recoil starter
handle. Grip frame; carefully pull up and push to tilt
generator backward.
3.
Gently set generator onto the recoil side or elevate
the generator by placing solid wood pieces under-
neath unit.
4.
Place a washer in the center of each rubber stopper.
5.
Attach a rubber stopper to the bottom of each support
leg using a 30 mm long hex flange bolt and a serrated
flange nut; tighten until securely seated.
6.
Attach each support leg to pre-drilled holes on bottom
of generator frame, using 16 mm long full-thread hex
flange bolts and serrated flange nuts; tighten until
securely seated.
To install support legs, you will need:
±
M8 x 30 mm long hex flange bolts (2)
±
M8 x 16 mm OD x 1.5 mm washers (2)
±
M8 serrated flange nuts (6)
±
M8 x 16 mm long full-thread hex flange bolts (4)
±
Brackets (2)
±
Rubber stoppers (2)
±
Socket wrench with 13 mm socket
*
*
Not included
Generator must be empty of engine oil and fuel.
Drain engine oil and fuel, if necessary.
Generator is heavy! Lifting generator can cause
back or other bodily injury. NEVER lift generator
without assistance.
FIGURE 5:
Tip onto Generator Recoil Side
CAUTION
FIGURE 6:
Rubber Stopper Attached to Support Leg
FIGURE 7:
Support Leg Attached to Generator