Husqvarna AUTOMOWER 450XH EPOS Owner Manual - Page 12

To examine where to put the power supply, max. 5 cm / 2

Get Husqvarna AUTOMOWER 450XH EPOS PDF manuals and user guides View all Husqvarna AUTOMOWER 450XH EPOS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

>110° 60° 10° max. 5 cm / 2" max. 5 cm / 2" A B • If the product must not operate in a part of the docking area, put a protective wall that is minimum 15 cm / 6 in. in height. The docking area (A) is a circular area around the charging station with a radius of 3 m / 9.8 ft. • If the work area has 2 parts separated with a steep slope, Husqvarna recommends to put the charging station in the lower section. CAUTION: Do not install the charging station where there are metal objects in the ground. Metal objects can cause interference with the charging station signal. 3.6 To examine where to put the power supply CAUTION: Make sure that the blades on the product do not cut the low-voltage cable. CAUTION: Do not put the low-voltage cable in a coil or below the charging station plate. The coil causes interference with the signal from the charging station. A Note: The product uses the charging station signal to search for the charging station when it is in the docking area. • Put the charging station near a power outlet. • Put the charging station on a level surface. • The baseplate of the charging station must not be bent. • Put the power supply in an area with a roof and protection from the sun and rain. • Put the power supply in an area with good airflow. • Use a residual-current device (RCD) with a tripping current of maximum 30 mA when you connect the power supply to the power outlet. Low-voltage cables of different lengths are available as accessories. 12 - Installation 1970 - 001 - 10.10.2022

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
>110°
60°
10°
B
A
•
If the product must not operate in a part of the
docking area, put a protective wall that is minimum
15 cm / 6 in. in height. The docking area (A) is
a circular area around the charging station with a
radius of 3 m / 9.8 ft.
A
Note:
The product uses the charging station
signal to search for the charging station when it
is in the docking area.
•
Put the charging station near a power outlet.
•
Put the charging station on a level surface.
•
The baseplate of the charging station must not be
bent.
max. 5 cm / 2"
max. 5 cm / 2"
•
If the work area has 2 parts separated with a steep
slope, Husqvarna recommends to put the charging
station in the lower section.
CAUTION:
Do not install the charging
station where there are metal objects
in the ground. Metal objects can cause
interference with the charging station signal.
3.6 To examine where to put the power
supply
CAUTION:
Make sure that the blades
on the product do not cut the low-voltage
cable.
CAUTION:
Do not put the low-voltage
cable in a coil or below the charging station
plate. The coil causes interference with the
signal from the charging station.
•
Put the power supply in an area with a roof and
protection from the sun and rain.
•
Put the power supply in an area with good airflow.
•
Use a residual-current device (RCD) with a tripping
current of maximum 30 mA when you connect the
power supply to the power outlet.
Low-voltage cables of different lengths are available as
accessories.
12
- Installation
1970 - 001 - 10.10.2022