Husqvarna AUTOMOWER 450XH EPOS Owner Manual - Page 27

Message, Cause, Action, Outside work area

Get Husqvarna AUTOMOWER 450XH EPOS PDF manuals and user guides View all Husqvarna AUTOMOWER 450XH EPOS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Message No loop signal Outside work area Cause Action The power supply or the low-voltage ca- If the LED indicator on the charging sta- ble for the charging station is not connec- tion is out, it shows that there is no pow- ted. er. Examine the power outlet connection and the residual-current device. Make sure that the low-voltage cable is con- nected to the charging station. The power supply or the low-voltage ca- Replace the power supply or low-voltage ble for the charging station is damaged. cable. ECO mode is enabled and the LED indicator of the charging station flashes green. The product was started manually in the work area but the STOP button was not pushed before the product was moved from the charging station. The charging station signal is disabled and the product cannot enter the charging station. Refer to ECO mode on page 19. Put the product in the charging station. Start the product. Refer to To start the product on page 22. The product does not find the loop signal Put the product in the charging station from the charging station. and make a new loop signal. Refer to New loop signal on page 20. The charging station in not installed correctly. Install the charging station according to the instruction. Refer to To install the charging station on page 14. Interference from metal objects such as Change the position of the charging stafences, reinforcement steel or buried ca- tion. bles near the charging station. The work area slopes too much by the virtual boundary. Make sure that the virtual boundary is installed correctly. Refer to To examine where to install the objects on the map on page 13. The transport path or the path to the maintenance point slopes too much. Make sure that the transport path is installed correctly. Refer to To install the map objects in a slope on page 13. The product can not find the correct Put the product in the charging station charging station signal because of inter- and make a new loop signal. Refer to ference with a loop signal from a different New loop signal on page 20. product installation nearby. Interference from metal objects such as Change the position of the charging stafences, reinforcement steel or buried ca- tion. bles near the charging station. 1970 - 001 - 10.10.2022 Troubleshooting - 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
Message
Cause
Action
No loop signal
The power supply or the low-voltage ca-
ble for the charging station is not connec-
ted.
If the LED indicator on the charging sta-
tion is out, it shows that there is no pow-
er. Examine the power outlet connection
and the residual-current device. Make
sure that the low-voltage cable is con-
nected to the charging station.
The power supply or the low-voltage ca-
ble for the charging station is damaged.
Replace the power supply or low-voltage
cable.
ECO mode
is enabled and the LED in-
dicator of the charging station flashes
green. The product was started manually
in the work area but the
STOP
button
was not pushed before the product was
moved from the charging station. The
charging station signal is disabled and
the product cannot enter the charging
station. Refer to
ECO mode on page 19
.
Put the product in the charging station.
Start the product. Refer to
To start the
product on page 22
.
The product does not find the loop signal
from the charging station.
Put the product in the charging station
and make a new loop signal. Refer to
New loop signal on page 20
.
The charging station in not installed cor-
rectly.
Install the charging station according to
the instruction. Refer to
To install the
charging station on page 14
.
Interference from metal objects such as
fences, reinforcement steel or buried ca-
bles near the charging station.
Change the position of the charging sta-
tion.
Outside work area
The work area slopes too much by the
virtual boundary.
Make sure that the virtual boundary is
installed correctly. Refer to
To examine
where to install the objects on the map
on page 13
.
The transport path or the path to the
maintenance point slopes too much.
Make sure that the transport path is in-
stalled correctly. Refer to
To install the
map objects in a slope on page 13
.
The product can not find the correct
charging station signal because of inter-
ference with a loop signal from a different
product installation nearby.
Put the product in the charging station
and make a new loop signal. Refer to
New loop signal on page 20
.
Interference from metal objects such as
fences, reinforcement steel or buried ca-
bles near the charging station.
Change the position of the charging sta-
tion.
1970 - 001 - 10.10.2022
Troubleshooting -
27