Husqvarna AUTOMOWER 450XH EPOS Owner Manual - Page 34

Symptoms, Cause, Action, Main switch

Get Husqvarna AUTOMOWER 450XH EPOS PDF manuals and user guides View all Husqvarna AUTOMOWER 450XH EPOS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

6.6 Symptoms If the product does not operate correctly, refer to the symptoms table below. Symptoms Cause Action The Main switch is set to the 0 position but the product is not set to OFF. The Main switch is set to the 0 posi- tion but the product is not connected to the Automower® Connect app with Bluetooth®. The product is disabled but not set to OFF. Set the Main switch to the 1 position, connect the product to the Automower® Connect app with Bluetooth® and set the Main switch to the 0 position. The product cannot go into the charging station. The charging station is not on a level sur- Put the charging station on a level sur- face. face. Refer to To examine where to put the charging station on page 11. The product operates at the incorrect time. The charging station is put too far from the work area. Make a new work area or move the charging station. The time and date of the product must be Set the time and date. Refer to Time & set. date on page 20. The start and stop time for operation are Change the schedule settings. Refer to incorrect. Schedule on page 18. There is vibration in the prod- The cutting system is not in balance be- uct. cause of damaged blades. Examine the blades and screws and replace them if necessary. Refer to To replace the blades on page 25. The cutting system is not in balance because of too many blades in the same position. Do a check that only one blade is attached to each screw. Blades of different thickness are installed Examine if the blades are of different on the product. thickness and replace the blades if nec- essary. The product operates, but the The product goes to the charging station. Usual operation of the product. The blade disc does not rotate. blade disc does not rotate when the product goes to the charging station. The product operates for shorter periods than usual between charges. Grass or other object causes a blockage Remove and clean the blade disc. Refer to the blade disc. to To clean the chassis and blade disc on page 24. The battery is at the end of its life cycle. Replace the battery. Refer to Battery on page 25. The grass is high and thick. Increase the cutting height and then decrease it when the grass is shorter. Operation and charging times The battery is at the end of its life cycle. Replace the battery. Refer to Battery on are shorter than usual. page 25. 34 - Troubleshooting 1970 - 001 - 10.10.2022

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
6.6 Symptoms
If the product does not operate correctly, refer to the symptoms table below.
Symptoms
Cause
Action
The
Main switch
is set to the
0
position but the product is
not set to OFF.
The
Main switch
is set to the
0
posi-
tion but the product is not connected to
the Automower
®
Connect app with Blue-
tooth
®
. The product is disabled but not
set to OFF.
Set the
Main switch
to the
1
position,
connect the product to the Automower
®
Connect app with Bluetooth
®
and set the
Main switch
to the
0
position.
The product cannot go into
the charging station.
The charging station is not on a level sur-
face.
Put the charging station on a level sur-
face. Refer to
To examine where to put
the charging station on page 11
.
The charging station is put too far from
the work area.
Make a new work area or move the
charging station.
The product operates at the
incorrect time.
The time and date of the product must be
set.
Set the time and date. Refer to
Time &
date on page 20
.
The start and stop time for operation are
incorrect.
Change the schedule settings. Refer to
Schedule on page 18
.
There is vibration in the prod-
uct.
The cutting system is not in balance be-
cause of damaged blades.
Examine the blades and screws and re-
place them if necessary. Refer to
To re-
place the blades on page 25
.
The cutting system is not in balance be-
cause of too many blades in the same
position.
Do a check that only one blade is attach-
ed to each screw.
Blades of different thickness are installed
on the product.
Examine if the blades are of different
thickness and replace the blades if nec-
essary.
The product operates, but the
blade disc does not rotate.
The product goes to the charging station.
Usual operation of the product. The
blade disc does not rotate when the
product goes to the charging station.
The product operates for
shorter periods than usual
between charges.
Grass or other object causes a blockage
to the blade disc.
Remove and clean the blade disc. Refer
to
To clean the chassis and blade disc on
page 24
.
The battery is at the end of its life cycle.
Replace the battery. Refer to
Battery on
page 25
.
The grass is high and thick.
Increase the cutting height and then de-
crease it when the grass is shorter.
Operation and charging times
are shorter than usual.
The battery is at the end of its life cycle.
Replace the battery. Refer to
Battery on
page 25
.
34
- Troubleshooting
1970 - 001 - 10.10.2022