Husqvarna MADSAW Owner Manual - Page 19

CAUTION, To lubricate the shaft, To apply dielectric grease to the, shaft coupling, To check

Get Husqvarna MADSAW PDF manuals and user guides View all Husqvarna MADSAW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

To clean the air filter CAUTION: An air filter that is damaged, very dirty, or soaked with fuel must always be replaced. Clean the air filter from dirt and dust regularly. This prevents carburetor malfunctions, starting problems, loss of engine power, wear to engine parts and more fuel consumption than usual. If you use an air filter for a long time, it cannot be fully cleaned. Replace the air filter with a new one at regular intervals. Refer to Maintenance schedule on page 16. 1. Move the choke lever up to close the choke valve. 2. Lubricate the end of the drive shaft. 3. Assemble the shaft. Refer to To assemble the shaft on page 10. To apply dielectric grease to the shaft coupling Apply dielectric grease to the inner surface of the shaft coupling and the outer surface of the shaft after each 30 hours of operation. 1. Disassemble the shaft. Refer to To disassemble the shaft on page 11. 2. Apply dielectric grease to the inner surface of the shaft coupling and the outer surface of the shaft. 2. Remove the air filter cover and the air filters. 3. Clean the air filters with warm soap water. 4. Replace the air filters if they cannot be fully cleaned. Always replace a damaged air filter. 5. Clean the inner surface of the air filter cover. Use compressed air or a brush. 6. Do a check of the rubber seal on the air filter. Replace the air filter if the rubber seal is damaged. 7. Make sure that the air filter is dry before you install it. To lubricate the shaft Lubricate the ends of the drive shaft after each 30 hours of operation. There is a risk that the ends of the drive shaft (splined coupling) wears if they are not lubricated regularly. 1. Disassemble the shaft. Refer to To disassemble the shaft on page 11. 3. Assemble the shaft. Refer to To assemble the shaft on page 10. To check the chain drive sprocket 1. Regularly check the degree of wear on the drive sprocket. Replace if wear is excessive. 1480 - 009 - 26.01.2022 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
To clean the air filter
CAUTION:
An air filter that is
damaged, very dirty, or soaked with fuel
must always be replaced.
Clean the air filter from dirt and dust regularly. This
prevents carburetor malfunctions, starting problems,
loss of engine power, wear to engine parts and more
fuel consumption than usual.
If you use an air filter for a long time, it cannot be
fully cleaned. Replace the air filter with a new one at
regular intervals. Refer to
Maintenance schedule on
page 16
.
1.
Move the choke lever up to close the choke
valve.
2.
Remove the air filter cover and the air filters.
3.
Clean the air filters with warm soap water.
4.
Replace the air filters if they cannot be fully
cleaned. Always replace a damaged air filter.
5.
Clean the inner surface of the air filter cover. Use
compressed air or a brush.
6.
Do a check of the rubber seal on the air
filter. Replace the air filter if the rubber seal is
damaged.
7.
Make sure that the air filter is dry before you
install it.
To lubricate the shaft
Lubricate the ends of the drive shaft after each 30
hours of operation. There is a risk that the ends of
the drive shaft (splined coupling) wears if they are
not lubricated regularly.
1.
Disassemble the shaft. Refer to
To disassemble
the shaft on page 11
.
2.
Lubricate the end of the drive shaft.
3.
Assemble the shaft. Refer to
To assemble the
shaft on page 10
.
To apply dielectric grease to the
shaft coupling
Apply dielectric grease to the inner surface of the
shaft coupling and the outer surface of the shaft after
each 30 hours of operation.
1.
Disassemble the shaft. Refer to
To disassemble
the shaft on page 11
.
2.
Apply dielectric grease to the inner surface of the
shaft coupling and the outer surface of the shaft.
3.
Assemble the shaft. Refer to
To assemble the
shaft on page 10
.
To check the chain drive sprocket
1.
Regularly check the degree of wear on the drive
sprocket. Replace if wear is excessive.
1480 - 009 - 26.01.2022
19