IBM 43635gu Installation Guide - Page 33

connectors

Get IBM 43635gu - Servers System X3200 Xeon 2.13ghz PDF manuals and user guides
UPC - 883436002950
View all IBM 43635gu manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

10. Connect one end of the applicable signal cable into the rear of the drive and make sure that the other end of this cable is connected into the applicable IDE or SATA connector on the system board. 11. Route the signal cable so that it does not block the airflow to the rear of the drives or over the microprocessor and dual inline memory modules (DIMMs). 12. If you have another drive to install or remove, do so now. 13. Connect the power cable to the rear of the drive. The connectors are keyed and can be inserted only one way. If you have other devices to install or remove, do so now; otherwise, go to "Completing the installation" on page 31. Installing a tape drive EMC shield Tape drive Drive retainer clip To install a tape drive, complete the following steps: 1. Read the safety information that begins on page v and "Installation guidelines" on page 7. 2. Turn off the server and peripheral devices, and disconnect the power cords and all external cables. 3. Remove the side cover (see "Removing the side cover" on page 10). 4. Remove the two-piece bezel (see "Removing the two-piece bezel" on page 11). 5. Use a screwdriver to pry the EMC shield away from the server. 6. Touch the static-protective package that contains the drive to any unpainted metal surface on the server; then, remove the drive from the package and place it on a static-protective surface. 7. Set any jumpers or switches on the drive according to the documentation that comes with the drive. Chapter 2. Installing optional devices 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
10.
Connect
one
end
of
the
applicable
signal
cable
into
the
rear
of
the
drive
and
make
sure
that
the
other
end
of
this
cable
is
connected
into
the
applicable
IDE
or
SATA
connector
on
the
system
board.
11.
Route
the
signal
cable
so
that
it
does
not
block
the
airflow
to
the
rear
of
the
drives
or
over
the
microprocessor
and
dual
inline
memory
modules
(DIMMs).
12.
If
you
have
another
drive
to
install
or
remove,
do
so
now.
13.
Connect
the
power
cable
to
the
rear
of
the
drive.
The
connectors
are
keyed
and
can
be
inserted
only
one
way.
If
you
have
other
devices
to
install
or
remove,
do
so
now;
otherwise,
go
to
“Completing
the
installation”
on
page
31.
Installing
a
tape
drive
Tape drive
EMC shield
Drive retainer clip
To
install
a
tape
drive,
complete
the
following
steps:
1.
Read
the
safety
information
that
begins
on
page
v
and
“Installation
guidelines”
on
page
7.
2.
Turn
off
the
server
and
peripheral
devices,
and
disconnect
the
power
cords
and
all
external
cables.
3.
Remove
the
side
cover
(see
“Removing
the
side
cover”
on
page
10).
4.
Remove
the
two-piece
bezel
(see
“Removing
the
two-piece
bezel”
on
page
11).
5.
Use
a
screwdriver
to
pry
the
EMC
shield
away
from
the
server.
6.
Touch
the
static-protective
package
that
contains
the
drive
to
any
unpainted
metal
surface
on
the
server;
then,
remove
the
drive
from
the
package
and
place
it
on
a
static-protective
surface.
7.
Set
any
jumpers
or
switches
on
the
drive
according
to
the
documentation
that
comes
with
the
drive.
Chapter
2.
Installing
optional
devices
19