IBM 8862 User Manual - Page 70

Remind, button

Get IBM 8862 - Eserver xSeries 365 PDF manuals and user guides
UPC - 000435172679
View all IBM 8862 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

3. The NR LED is lit only when two power supplies are installed and one is not functioning. Remind button You can use the Remind button to place the system-error LED on the front panel into the remind mode (flashes every 2 seconds). By pressing the button, you acknowledge the failure but indicate that you will not take immediate action. If a new failure occurs, the system-error LED turns on again. The system-error LED stays in Remind mode until one of the following conditions occurs: v All known problems are resolved v The system is restarted v A new problem occurs You can use the Remind button to delay server maintenance until a later time. The Light Path Diagnostics feature might direct you to look for an LED that identifies the specific failing component on the internal boards. See the Option Installation Guide for illustrations that identify the LEDs on the boards. See the solving problems section in the Hardware Maintenance Manual and Troubleshooting Guide on the IBM xSeries Documentation CD for more information. 58 xSeries 365 Type 8861 and 8862: Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
3.
The
NR
LED
is
lit
only
when
two
power
supplies
are
installed
and
one
is
not
functioning.
Remind
button
You
can
use
the
Remind
button
to
place
the
system-error
LED
on
the
front
panel
into
the
remind
mode
(flashes
every
2
seconds).
By
pressing
the
button,
you
acknowledge
the
failure
but
indicate
that
you
will
not
take
immediate
action.
If
a
new
failure
occurs,
the
system-error
LED
turns
on
again.
The
system-error
LED
stays
in
Remind
mode
until
one
of
the
following
conditions
occurs:
v
All
known
problems
are
resolved
v
The
system
is
restarted
v
A
new
problem
occurs
You
can
use
the
Remind
button
to
delay
server
maintenance
until
a
later
time.
The
Light
Path
Diagnostics
feature
might
direct
you
to
look
for
an
LED
that
identifies
the
specific
failing
component
on
the
internal
boards.
See
the
Option
Installation
Guide
for
illustrations
that
identify
the
LEDs
on
the
boards.
See
the
solving
problems
section
in
the
Hardware
Maintenance
Manual
and
Troubleshooting
Guide
on
the
IBM
xSeries
Documentation
CD
for
more
information.
58
xSeries
365
Type
8861
and
8862:
Installation
Guide