Icom IC-F8101 Instruction Manual - Page 26

Phone call, Sending a Phone call

Get Icom IC-F8101 PDF manuals and user guides View all Icom IC-F8101 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

4 SELCALL/ALE OPERATION DDPhone call Allows you to make Phone calls through a telephone interconnect service provider. • Preparation for a Phone call Send a Channel Test call on several Phone call channels, and check the propagation on each one to select the channel with the best signal quality. (p. 26) • Sending a Phone call qqHold down [ ] for 1 second to enter the Network selection screen. wwPush [r] or [s] to select the desired Network, and then push [ ]. • The Networks that belong to the Icom Selcall or Open Selcall systems must be selected. uuPush [r] or [s] to select the Channel. • Only the channels that belong to the selected Network in step w, are displayed. • If desired, push [Tests](§§) to transmit the Channel Test call in this step. iiPush [ ] to transmit the Phone call. The call is stored in the Call Out memory. • While calling, push [PTT] to cancel the call. You can also make a Phone call when the Address screen is displayed. In this case, you can skip several steps, see page 29 for the Simple Selcall operation details. eePush [r] or [s] to select the Call Type to "Phone." • "Selective," "Phone," "Message," "Send Position," "Get Position," "Get Status," "Emergency," "Channel Test" and "Stun" are selectable. The Get Status call is selectable in the Icom Selcall, and the Stun call is selectable in the Open Selcall. rrPush keypad to enter the Number, and then push [ ]. • The previously entered Number is displayed. • Push [t](§) or [u](§§§) to move the cursor. • Push [8] to delete the digit to the left of the cursor. • This Number is not stored in the Number list. ttPush keypad to enter the Phone Link ID, and then push [ ]. • The previously entered Link ID is displayed. • Push [t](§) or [u](§§§) to move the cursor. • Push [8] to delete the digit to the left of the cursor. • This ID is not stored in the Phone Link ID list. • After a Phone call q When a Phone call is finished, push [ ] to trans- mit the disconnect call. • Until the Disconnect call is transmitted, the telephone interconnect service provider continues counting the time for toll charging. • If the "Auto Start Type" item of "Setmode" is set to "Scan" or "Termination," the Call automatically disconnects after the Auto Start Wait Time period has past with no operation. (Setmode > Call) yyPush [r] or [s] to select the Profile, then push [ ]. 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
20
4
SELCALL/ALE OPERATION
Allows you to make Phone calls through a telephone
interconnect service provider.
• Preparation for a Phone call
Send a Channel Test call on several Phone call chan-
nels, and check the propagation on each one to select
the channel with the best signal quality. (p. 26)
•
Sending a Phone call
Hold down
q
[
]
for 1 second to enter the Network
selection screen.
Push
w
[
r
]
or
[
s
]
to select the desired Network, and
then push
[
]
.
• The Networks that belong to the Icom Selcall or Open
Selcall systems must be selected.
Push
e
[
r
]
or
[
s
]
to select the Call Type to “Phone.”
• “Selective,” “Phone,” “Message,” “Send Position,” “Get Posi
-
tion,” “Get Status,” “Emergency,” “Channel Test” and “Stun”
are selectable.
The Get Status call is selectable in the Icom Selcall,
and the Stun call is selectable in the Open Selcall.
Push keypad to enter the Number, and then push
r
[
]
.
• The previously entered Number is displayed.
• Push
[
t
]
(
§
) or
[
u
]
(
§§§
)
to move the cursor.
• Push
[
8
]
to delete the digit to the left of the cursor.
• This Number is not stored in the Number list.
Push keypad to enter the Phone Link ID, and then
t
push
[
]
.
• The previously entered Link ID is displayed.
• Push
[
t
]
(
§
) or
[
u
]
(
§§§
)
to move the cursor.
• Push
[
8
]
to delete the digit to the left of the cursor.
• This ID is not stored in the Phone Link ID list.
Push
y
[
r
]
or
[
s
]
to select the Profile, then push
[
]
.
Push
u
[
r
]
or
[
s
]
to select the Channel.
• Only the channels that belong to the selected Network in
step
w
, are displayed.
• If desired, push
[Tests]
(
§§
) to transmit the Channel Test
call in this step.
Push
i
[
]
to transmit the Phone call. The call is
stored in the Call Out memory.
• While calling, push
[PTT]
to cancel the call.
You can also make a Phone call when the Address
screen is displayed. In this case, you can skip sev-
eral steps, see page 29 for the Simple Selcall opera-
tion details.
• After a Phone call
q
When a Phone call is finished, push
[
]
to trans-
mit the disconnect call.
• Until the Disconnect call is transmitted, the telephone
interconnect service provider continues counting the
time for toll charging.
• If the “Auto Start Type” item of “Setmode” is set to “Scan”
or “Termination,” the Call automatically disconnects after
the Auto Start Wait Time period has past with no opera-
tion.
(Setmode > Call)
Phone call
D