Icom IC-M424 Instruction Manual - Page 97

■ Microphone installation, Installation

Get Icom IC-M424 PDF manuals and user guides View all Icom IC-M424 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 97 highlights

CONNECTIONS AND MAINTENANCE 10 ■■Microphone installation The optional HM-195 should be connected to the transceiver using the supplied OPC-1540 connection cable. The cable is used to operate from a longer distance. The cable connector can also be installed as a built-in plug on a cabinet or wall. To operate from even longer distances, the optional 6 meter long OPC-1541 extension cable can be used between the transceiver and the OPC-1540. Up to two OPC-1541 can be added. DDInstallation qqInsert the OPC-1540 cable connector into the command microphone jack, and tighten the nut. wwTo use the cable connector as a wall socket, install it as described to the right. 1 eeUsing the mounting base as a template, carefully mark the 2 holes where the cable and three screws will be fastened. 3 rrDrill holes at these marks. ttInstall the mounting base using the supplied screws, as 4 shown below. 5 Mounting base Nut 6 7 8 Gasket 9 10 Screw holes (approx. 2 (d) mm; 3⁄32˝) Cap 11 yyThe completed installation should look like this. 12 13 14 15 16 88

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
88
10
CONNECTIONS AND MAINTENANCE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Microphone installation
■
The optional HM-195 should be connected to the transceiver
using the supplied OPC-1540 connection cable.
The
cable is used to operate from a longer distance. The
cable connector can also be installed as a built-in plug on a
cabinet or wall.
To operate from even longer distances, the optional 6 meter
long OPC-1541 extension cable can be used between the
transceiver and the OPC-1540. Up to two OPC-1541 can be
added.
Installation
D
Insert the OPC-1540 cable connector into the command
q
microphone jack, and tighten the nut.
To use the cable connector as a wall socket, install it as
w
described to the right.
Using the mounting base as a template, carefully mark the
e
holes where the cable and three screws will be fastened.
Drill holes at these marks.
r
Install the mounting base using the supplied screws, as
t
shown below.
Gasket
Cap
Mounting base
Nut
Screw holes
(approx. 2 (d) mm;
3
/
32
˝)
The completed installation should look like this.
y