Icom ID-51A PLUS Instruction Manual - Page 73

■Troubleshooting

Get Icom ID-51A PLUS PDF manuals and user guides View all Icom ID-51A PLUS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

D-STAR OPERATION 6 ■■Troubleshooting To communicate through the repeater, your signal must access to the repeater. When your signal accesses your local repeater, but it is not sent to the destination repeater, the repeater replies with an status message. PROBLEM POSSIBLE CAUSE SOLUTION REF. After your call, the repeater does • The repeater setting is wrong. not return a status reply. • Y our transmission did not reach the repeater. • Select the correct repeater. p. 47 • Correct the repeater frequency, frequency off- - set, or duplex settings. • W ait until you are closer to the repeater and - try again. • Try to access another repeater. After your call, the repeater re- • T he call was successfully sent, but no station • Wait for a while, and try again. plies 'UR?' and its call sign. immediately replied. - 6 D-STAR OPERATION After your call, the repeater replies • Y our own call sign (MY) has not been set. • Set your own call sign (MY). p. 13 'RX' or 'RPT?' and the access re- • Y our own call sign (MY) has not been regis- • Register your own call sign (MY) on a gateway p. 15 peater's call sign. tered on a gateway repeater, or the registered repeater, or confirm the registration of the call contents do not match your transceiver's set- sign. ting. After your call, the repeater re- • T he repeater cannot connect to the destina- • C heck the repeater setting. plies 'RPT?' and call sign of the tion repeater. destination repeater. • T he repeater is busy. • W ait for a while, and try it again. p. 57 - ☞☞Continued on the next page 60

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
60
6
D-STAR OPERATION
6
PROBLEM
POSSIBLE CAUSE
SOLUTION
REF.
After your call, the repeater does
not return a status reply.
• The repeater setting is wrong.
•Your transmission did not reach the repeater.
• Select the correct repeater.
• Correct the repeater frequency, frequency off
-
set, or duplex settings.
• Wait until you are closer to the repeater and
try again.
• Try to access another repeater.
p. 47
—
—
After your call, the repeater re-
plies ‘UR?’ and its call sign.
• The call was successfully sent, but no station
immediately replied.
• Wait for a while, and try again.
—
After your call, the repeater replies
‘RX’ or ‘RPT?’ and the access re
-
peater’s call sign.
•Your own call sign (MY) has not been set.
•Your own call sign (MY) has not been regis
-
tered on a gateway repeater, or the registered
contents do not match your transceiver’s set-
ting.
• Set your own call sign (MY).
• Register your own call sign (MY) on a gateway
repeater, or confirm the registration of the call
sign.
p. 13
p. 15
After your call, the repeater re-
plies ‘RPT?’ and call sign of the
destination repeater.
• The repeater cannot connect to the destina
-
tion repeater.
• The repeater is
busy.
•
Check the repeater setting.
•
Wait for a while, and try it again.
p. 57
—
■
Troubleshooting
To communicate through the repeater, your signal must access to the repeater. When your signal accesses your local repeater,
but it is not sent to the destination repeater, the repeater replies with an status message.
D-STAR OPERATION
Continued on the next page
☞