Icom ID-51A PLUS Instruction Manual - Page 74

PROBLEM, POSSIBLE CAUSE, Troubleshooting Continued - 2 software

Get Icom ID-51A PLUS PDF manuals and user guides View all Icom ID-51A PLUS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

6 D-STAR OPERATION ■■ Troubleshooting (Continued) PROBLEM POSSIBLE CAUSE SOLUTION REF. After your call, the access repeat- • T he call sign of the destination repeater is • Correctly set the destination repeater call sign. - er replies 'RPT?' and its call sign. wrong. Even holding down , the DR • There is no repeater list in your radio. screen will not appear. • Reload the repeater list using the CS-51PLUS Section cloning software on the CD or from a mi- 17 of AI* croSD backup card. • Enter the Repeater list data directly into the Section transceiver. 9 of AI* Even holding down , the re- • T he call sign has not been correctly received. • T ry it again, after the transceiver has correctly - ceived call sign will not set to the • W hen a received signal is weak, or a signal received the call sign. destination call sign. is received during scanning, the call sign may not be received correctly. In that case, "--------" appears and error beeps sound, and a reply call cannot be made. A Local area call can be made, • MY call sign has not been registered on a D- • Register your own call sign (MY) on a gateway p. 15 but the Gateway call or destina- STAR repeater. repeater, or confirm the registration of the call tion station call cannot be made. sign. Position data cannot be received • "External GPS" is selected in the GPS Set • Connect an external GPS receiver. or displayed. item on the Menu screen, but an external GPS receiver is not connected. • "OFF" or "Manual" is selected in the GPS Set • Select either "Internal GPS" or "External GPS" item on the Menu screen. in the GPS Set item on the Menu screen. • A GPS signal was not received. • Move until the GPS signal is received. "L" appears on the LCD. • W hile receiving through the internet, some • Wait a while, and try it again. - packets may be lost due to network error When the transceiver receives corrupted (poor data throughput performance). data, and misidentifies it is as Packet Loss, "L" is displayed, even if it is a Local area call. "DV" and "FM" icons alternately • W hile in the DV mode, an FM signal is re- • Use a different operating frequency until there - blink. ceived. are no FM signals on the original frequency. * "AI" indicates the PDF type Advanced Instructions. 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
61
6
D-STAR OPERATION
PROBLEM
POSSIBLE CAUSE
SOLUTION
REF.
After your call, the access repeat-
er replies ‘RPT?’ and its call sign.
• The call sign of the destination repeater is
wrong.
• Correctly set the destination repeater call sign.
—
Even holding down
, the DR
screen will not appear.
• There is no repeater list in your radio.
• Reload the repeater list using the CS-51PLUS
CLONING
SOFTWARE
on the CD or from a mi-
croSD backup card.
• Enter the Repeater list data directly into the
transceiver.
Section
17 of AI*
Section
9 of AI*
Even holding down
, the re-
ceived call sign will not set to the
destination call sign.
• The call sign has not been correctly received.
• When a received signal is weak, or a signal
is received during scanning, the call sign may
not be received correctly. In that case, “--------”
appears and error beeps sound, and a reply
call cannot be made.
• Try it again, after the transceiver has correctly
received the call sign.
—
A Local area call can be made,
but the Gateway call or destina-
tion station call cannot be made.
• MY call sign has not been registered on a D-
STAR repeater.
•
Register your own call sign (MY) on a gateway
repeater, or confirm the registration of the call
sign.
p. 15
Position data cannot be received
or displayed.
• “External GPS” is selected in the GPS Set
item on the Menu screen, but an external
GPS receiver is not connected.
• “OFF” or “Manual” is selected in the GPS Set
item on the Menu screen.
• A GPS signal was not received.
• Connect an external GPS receiver.
• Select either “Internal GPS” or “External GPS”
in the GPS Set item on the Menu screen.
• Move until the GPS signal is received.
“L” appears on the LCD.
•
While receiving through the internet, some
packets may be lost due to network error
(poor data throughput performance).
• Wait a while, and try it again.
When the transceiver receives corrupted
data, and misidentifies it is as Packet Loss, “L”
is displayed, even if it is a Local area call.
—
“DV” and “FM” icons alternately
blink.
•
While in the DV mode, an FM signal is re-
ceived.
• Use a different operating frequency until there
are no FM signals on the original frequency.
—
* “AI” indicates the PDF type Advanced Instructions.
Troubleshooting (Continued)
■