Invacare TER Owners Manual - Page 29

Removing/Installing Foldover Back Upholstery, Adjustable Tension Back Upholstery

Get Invacare TER PDF manuals and user guides View all Invacare TER manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Removing/Installing Foldover Back Upholstery SECTION 4-BACK ƽ WARNING The position of the footrest, seat angle, back angle, seating system/upholstery, castor size and position, rear wheel size and position, use of anti-tippers, as well as the user condition directly relate to the stability of the wheelchair. Any change to one or any combination of the ten may cause the wheelchair to decrease in stability. EXTREME care MUST be taken when changing the stability of the wheelchair. Refer to the chart in General Guidelines on page 14 of this manual. NOTE: For this procedure, refer to FIGURE 4.5. Removing Foldover Back Upholstery 1. Unfasten the two fastening flaps that secure the bottom of the existing back upholstery to the back posts. 2. Unfold the top of the back upholstery. 3. Lift up on the existing back upholstery and remove from the wheelchair. Installing Foldover Back Upholstery 1. Install the new back upholstery onto the back posts. 2. Wrap the end of a fastening flap around the back post. 3. Insert the end of the fastening flap through the loop. 4. Wrap the fastening flap around the back post again and press firmly to secure. 5. Fold the top of the back upholstery down over the back posts towards the front of the wheelchair. 6. Press firmly to secure the fastening strips. Back Upholstery Front of Wheelchair Fastening Strips Fold Fastening Flap Fastening Flap Loops Back Posts FIGURE 4.5 Removing/Installing Foldover Back Upholstery Adjustable Tension Back Upholstery ƽ WARNING The position of the footrest, seat angle, back angle, seating system/upholstery, castor size and position, rear wheel size and position, use of anti-tippers, as well as the user condition directly relate to the stability of the wheelchair. Any change to one or any combination of the ten may cause the wheelchair to decrease in stability. EXTREME care MUST be taken when changing the stability of the wheelchair. Refer to the chart in General Guidelines on page 14 of this manual. NOTE: For this procedure, refer to FIGURE 4.6. Part No 1122172 29 Everyday Series Wheelchairs/Sport Series Wheelchairs

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
SECTION 4—BACK
Part No 1122172
29
Everyday Series Wheelchairs/Sport Series Wheelchairs
Removing/Installing Foldover Back Upholstery
±
WARNING
The position of the footrest, seat angle, back angle, seating system/upholstery, castor size and
position, rear wheel size and position, use of anti-tippers, as well as the user condition directly
relate to the stability of the wheelchair. Any change to one or any combination of the ten may
cause the wheelchair to decrease in stability. EXTREME care MUST be taken when changing the
stability of the wheelchair. Refer to the chart in General Guidelines
on page 14 of this manual.
NOTE: For this procedure, refer to FIGURE 4.5.
Removing Foldover Back Upholstery
1.
Unfasten the two fastening flaps that secure the bottom of the existing back upholstery to the back posts.
2.
Unfold the top of the back upholstery.
3.
Lift up on the existing back upholstery and remove from the wheelchair.
Installing Foldover Back Upholstery
1.
Install the new back upholstery onto the back posts.
2.
Wrap the end of a fastening flap around the back post.
3.
Insert the end of the fastening flap through the loop.
4.
Wrap the fastening flap around the back post again and press firmly to secure.
5.
Fold the top of the back upholstery down over the back posts towards the front of the wheelchair.
6.
Press firmly to secure the fastening strips.
FIGURE 4.5
Removing/Installing Foldover Back Upholstery
Adjustable Tension Back Upholstery
±
WARNING
The position of the footrest, seat angle, back angle, seating system/upholstery, castor size and
position, rear wheel size and position, use of anti-tippers, as well as the user condition directly
relate to the stability of the wheelchair. Any change to one or any combination of the ten may
cause the wheelchair to decrease in stability. EXTREME care MUST be taken when changing the
stability of the wheelchair. Refer to the chart in General Guidelines
on page 14 of this manual.
NOTE: For this procedure, refer to FIGURE 4.6.
Fastening
Flap
Back Upholstery
Fold
Fastening
Flap
Back
Posts
Fastening
Strips
Loops
Front of Wheelchair