Invacare TER Owners Manual - Page 32

Wheels - telephone number

Get Invacare TER PDF manuals and user guides View all Invacare TER manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

SECTION 5-WHEELS SECTION 5-WHEELS ƽ WARNING After any adjustments, repair or service and before use, make sure all attaching hardware is tightened securely - otherwise injury or damage may result. Removing/Installing Rear Wheels CAUTION Changing the size of the rear wheels can affect the performance of the wheelchair. Contact Invacare at the telephone numbers on the back of this manual before changing rear wheel size. NOTE: For this procedure, refer to FIGURE 5.1. 1. Perform one of the following: • Quick‐Release ‐ Push in the tip of the quick‐release axle and pull axle and wheel away from the wheelchair. • Quad‐Release ‐ Lift up on the handle of the quad‐release axle and pull axle and wheel away from the wheelchair. 2. Repeat STEP 1 for the opposite rear wheel. 3. Reinstall the rear wheels onto the wheelchair by reversing STEPS 1‐2. ƽ WARNING Quick-Release Axle Wheelchair Frame Pull on the rear wheel to make sure the detent pin and locking pins of the quick/ quad-release axle are fully released before operating wheelchair. Keep locking pins clean. Detent Pin Rear Wheel Locking Pins 4. If there is too much movement of the rear wheel assembly in a back and forth motion, refer to Adjusting Quick‐Release Axles on page 32 or Adjusting Quad‐Release Handles on page 33. NOTE: Quad‐Release Axle not shown. Locking pins on the Quad‐Release Axle are the same as Quick‐Release Axle. FIGURE 5.1 Removing/Installing Rear Wheels Adjusting Quick-Release Axles NOTE: For this procedure, refer to FIGURE 5.2. 1. Remove rear wheel and quick‐release axle from the wheelchair. Refer to Removing/Installing Rear Wheels on page 32. 2. Depress detent pin in the quick‐release axle and slide axle through the wheel hub. 3. Release detent pin ensuring that the locking pins are fully released. 4. Increase or decrease end play by adjusting the locknut on the end of the quick‐release axle. 5. Reinstall rear wheel onto the wheelchair. Refer to Removing/Installing Rear Wheels on page 32. Adjustable Axle Position Camber Bar Locking Pins Locknut Detent Pin Wheel Hub Quick-Release Axle NOTE: End of Quick Release axle is shown for reference only. It is not visible when inserted into camber bar. FIGURE 5.2 Adjusting Quick-Release Axles Everyday Series Wheelchairs/Sport Series Wheelchairs 32 Part No 1122172

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
SECTION 5—WHEELS
Everyday Series Wheelchairs/Sport Series Wheelchairs
32
Part No 1122172
SECTION 5—WHEELS
±
WARNING
After any adjustments, repair or service and before use, make sure all attaching hardware is
tightened securely - otherwise injury or damage may result.
Removing/Installing Rear Wheels
CAUTION
Changing the size of the rear wheels can affect the performance of the wheelchair. Contact Inva-
care at the telephone numbers on the back of this manual before changing rear wheel size.
NOTE: For this procedure, refer to FIGURE 5.1.
1.
Perform one of the following:
•
Quick
‐
Release
‐
Push in the tip of the quick
‐
release axle and pull axle and wheel away from the wheelchair.
•
Quad
‐
Release
‐
Lift up on the handle of the quad
‐
release axle and pull axle and wheel away from the wheelchair.
2.
Repeat STEP 1 for the opposite rear wheel.
3.
Reinstall the rear wheels onto the wheelchair by
reversing STEPS 1
‐
2.
±
WARNING
Pull on the rear wheel to make sure the detent
pin and locking pins of the quick/ quad-release
axle are fully released before operating
wheelchair.
Keep locking pins clean.
4.
If there is too much movement of the rear wheel
assembly in a back and forth motion, refer to Adjusting
Quick
‐
Release Axles
on page 32 or Adjusting
Quad
‐
Release Handles
on page 33.
FIGURE 5.1
Removing/Installing Rear Wheels
Adjusting Quick-Release Axles
NOTE: For this procedure, refer to FIGURE 5.2.
1.
Remove rear wheel and quick
‐
release axle from the
wheelchair. Refer to Removing/Installing Rear Wheels
on page 32.
2.
Depress detent pin in the quick
‐
release axle and slide
axle through the wheel hub.
3.
Release detent pin ensuring that the locking pins are
fully released.
4.
Increase or decrease end play by adjusting the locknut
on the end of the quick
‐
release axle.
5.
Reinstall rear wheel onto the wheelchair. Refer to
Removing/Installing Rear Wheels
on page 32.
FIGURE 5.2
Adjusting Quick-Release Axles
Wheelchair Frame
Rear Wheel
Locking
Pins
Quick-Release
Axle
Detent Pin
NOTE: Quad
‐
Release Axle not shown. Locking pins on the
Quad
‐
Release Axle are the same as Quick
‐
Release Axle.
Locking Pins
Quick-Release Axle
Detent Pin
Locknut
Adjustable Axle Position
Camber Bar
Wheel Hub
NOTE: End of Quick Release axle is shown for reference only.
It is not visible when inserted into camber bar.