Invacare TER Owners Manual - Page 61

Wing/bumper

Get Invacare TER PDF manuals and user guides View all Invacare TER manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

SECTION 9-WING/BUMPER SECTION 9-WING/BUMPER ƽ WARNING After any adjustments, repair or service and before use, make sure all attaching hardware is tightened securely - otherwise injury or damage may occur. The bumper design creates a potential foot entrapment area. Ensure the occupant's legs and feet are properly secured during use. When transferring the occupant, ensure the feet do not slip between the bumper and the footrests. NOTE: The following procedures are for Transformer wheelchairs ONLY. Installing/Removing the Wing/Bumper NOTE: PSSA, PSST, and SPRO wings/bumper are not removable. NOTE: For this procedure, refer to FIGURE 9.1. Installing 1. Slide wing/bumper clamps onto castor housing on the Transformer. Ensure the wing or bumper is even on both sides. 2. Tighten allen screws securely on each side. Removing 1. Loosen allen screws on wing/bumper clamps. 2. Slide up and remove. Bumper/Wing Clamp Allen Screws Wing/Bumper Castor Housing FIGURE 9.1 Installing/Removing the Wing/Bumper Part No 1122172 61 Everyday Series Wheelchairs/Sport Series Wheelchairs

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
SECTION 9—WING/BUMPER
Part No 1122172
61
Everyday Series Wheelchairs/Sport Series Wheelchairs
SECTION 9—WING/BUMPER
±
WARNING
After any adjustments, repair or service and before use, make sure all attaching hardware is
tightened securely - otherwise injury or damage may occur.
The bumper design creates a potential foot entrapment area. Ensure the occupant’s legs and
feet are properly secured during use. When transferring the occupant, ensure the feet do not slip
between the bumper and the footrests.
NOTE: The following procedures are for Transformer wheelchairs ONLY.
Installing/Removing the Wing/Bumper
NOTE: PSSA, PSST, and SPRO wings/bumper are not removable.
NOTE: For this procedure, refer to FIGURE 9.1.
Installing
1.
Slide wing/bumper clamps onto castor housing on the Transformer. Ensure the wing or bumper is even on both sides.
2.
Tighten allen screws securely on each side.
Removing
1.
Loosen allen screws on wing/bumper clamps.
2.
Slide up and remove.
FIGURE 9.1
Installing/Removing the Wing/Bumper
Wing/Bumper
Castor Housing
Allen Screws
Bumper/Wing
Clamp