JVC DR-DX5S Instruction Manual - Page 69

SYSTEM CONNECTIONS, Connecting To A Dolby Digital Decoder Or An Amplifier With Built-in DTS

Get JVC DR-DX5S PDF manuals and user guides View all JVC DR-DX5S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

Connecting To A Dolby Digital Decoder Or An Amplifier With Built-in DTS These instructions enable you to connect your unit to a Dolby Digital Decoder or an amplifier with built-in DTS. Dolby Digital Decoder or amplifier with built-in DTS To DIGITAL AUDIO input Coaxial cable (not supplied) To [DIGITAL AUDIO OUT (COAXIAL)] Optical cable (not supplied) To [DIGITAL AUDIO OUT (OPTICAL)] SYSTEM CONNECTIONS EN 69 1 Connect the unit and a Dolby Digital Decoder or an amplifier with built-in DTS using either an optional optical cable or an optional coaxial cable. NOTES: ● For Dolby Digital sound, set ADIGITAL AUDIO OUTB to ADOLBY DIGITAL/PCMB. (A pg. 70) ● For DTS sound, set ADIGITAL AUDIO OUTB to ASTREAM/PCMB. (A pg. 70) CAUTIONS: ● This unit has a dynamic range of more than 110 dB with regards to its Hi-Fi audio capability. It is recommended that you check the maximum level if you are going to listen to the Hi-Fi audio signals through a stereo amplifier. A sudden surge in the input level to the speakers may damage them. ● Some speakers and televisions are specially shielded to prevent television interference. If both are of the non-shielded type, do not place the speakers adjacent to the TV set as this can adversely affect the playback picture. Rear of unit Note for connection: Remove the protection cap from the optical cable.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
EN
69
SYSTEM CONNECTIONS
These instructions enable you to connect your unit to a Dolby
Digital Decoder or an amplifier with built-in DTS.
1
Connect the unit and a Dolby Digital Decoder or an amplifier
with built-in DTS using either an optional optical cable or an
optional coaxial cable.
NOTES:
●
For Dolby Digital sound, set
A
DIGITAL AUDIO OUT
B
to
A
DOLBY
DIGITAL/PCM
B
. (
A
pg. 70)
●
For DTS sound, set
A
DIGITAL AUDIO OUT
B
to
A
STREAM/PCM
B
.
(
A
pg. 70)
CAUTIONS:
●
This unit has a dynamic range of more than 110 dB with regards
to its Hi-Fi audio capability. It is recommended that you check the
maximum level if you are going to listen to the Hi-Fi audio signals
through a stereo amplifier. A sudden surge in the input level to
the speakers may damage them.
●
Some speakers and televisions are specially shielded to prevent
television interference. If both are of the non-shielded type, do not
place the speakers adjacent to the TV set as this can adversely
affect the playback picture.
Connecting To A Dolby Digital Decoder
Or An Amplifier With Built-in DTS
Dolby Digital Decoder or
amplifier with built-in DTS
Coaxial cable
(not supplied)
Rear of unit
Note for connection:
Remove the protection cap from the
optical cable.
To [DIGITAL AUDIO
OUT (COAXIAL)]
To DIGITAL AUDIO input
Optical cable
(not supplied)
To [DIGITAL AUDIO
OUT (OPTICAL)]