JVC SR-VS20U 76 pg User's Manual on the SR-VS20U (1776KB, PDF) - Page 61

Reset The Counter, Vhs Deck Only, Locate Start Point, Engage Insert Editing, Start Editing, End

Get JVC SR-VS20U - Dual Format S-vhs/minidv Recorder PDF manuals and user guides View all JVC SR-VS20U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

STOP PLAY INSERT A. DUB PAUSE C.RESET T 1 4 W 2 5 3 2 6 7 8 9 0 4 PLAY 1 DV S-VHS STOP PAUSE 3 JOG JOG/SHUTTLE SHUTTLE EN 61 RESET THE COUNTER (VHS deck only) 5 Press C.RESET to change the counter display to "0:00:00". LOCATE START POINT 6 Determine the edit-in point (the beginning of the segment to be replaced) using the JOG/SHUTTLE controls or pressing ™£ and PAUSE. ● Be sure to engage the Still mode at the edit-in point. ENGAGE INSERT EDITING 7 Press INSERT. ● Your VCR enters the Insert-Pause mode. ( , and light up on the front display panel.) ● The TV screen changes from the still picture to the input source you are going to record. 8 START EDITING Load the source cassette and play back the segment that is to be inserted. When you reach the start of the section of the source tape that you wish to insert, press PLAY to start the tape in your VCR; Insert Editing begins at this point. ● and are displayed on the front display panel. 9 END INSERT EDITING VHS deck At counter "0:00:00", Insert Editing will stop automatically while the tape continues running in the Play mode. If you wish to stop Insert Editing before the specified edit-out point, press C.RESET. DV deck Press STOP to stop the tape in the DV deck. FOR AV INSERT EDITING (VHS deck only) If you want to replace the picture, Hi-Fi audio soundtrack and normal audio soundtrack all at the same time... In step 7 above, after you press INSERT, press A. DUB. also. ( and blink and lights up on the display panel.) NOTES: ● Once the Insert Editing starts, you can not use the other deck. ● Insert Editing cannot be performed on a VHS/S-VHS cassette that has had its record safety tab removed, or on a Mini DV cassette that has had its erase protection switch set to "SAVE". ● In insert editing, the recording speed (SP/EP) is determined by the previous recording to be replaced. If the previous recording's speed changes within a single edit, the inserted picture will be distorted at the switching point. (VHS deck only) ● A small portion of the recording which precedes an insert edit may become erased. ● Insert Editing is also possible using the rear connectors. When using these connectors, be sure to select the correct REAR AUX INPUT. To select the correct REAR AUX INPUT ("VIDEO" or "S-VIDEO"), follow steps 5, 8, and 9 from the "Edit From A Camcorder" section, ੬ pg 55. ● Insert Editing is not possible using the DV IN/OUT connector.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
EN
61
1
2
3
4
5
6
7
8
9
0
2
4
1
3
T
W
DV
S-VHS
RESET THE COUNTER
(VHS deck only)
5
Press
C.RESET
to change the counter display to
"0:00:00".
LOCATE START POINT
6
Determine the edit-in point (the beginning of the
segment to be replaced) using the
JOG/SHUTTLE
controls or pressing
™£
and
PAUSE
.
●
Be sure to engage the Still mode at the edit-in point.
ENGAGE INSERT EDITING
7
Press
INSERT
.
●
Your VCR enters the Insert-Pause mode. (
,
and
light up on the front display panel.)
●
The TV screen changes from the still picture to the
input source you are going to record.
START EDITING
8
Load the source cassette and play back the segment
that is to be inserted. When you reach the start of the
section of the source tape that you wish to insert, press
PLAY
to start the tape in your VCR; Insert Editing begins
at this point.
●
and
are displayed on the front display panel.
END INSERT EDITING
9
VHS deck
At counter "0:00:00", Insert Editing will stop automati-
cally while the tape continues running in the Play
mode. If you wish to stop Insert Editing before the
specified edit-out point, press
C.RESET
.
DV deck
Press
STOP
to stop the tape in the DV deck.
FOR AV INSERT EDITING (VHS deck only)
If you want to replace the picture, Hi-Fi audio soundtrack and
normal audio soundtrack all at the same time...
In step
7
above, after you press
INSERT
, press
A. DUB.
also.
(
and
blink and
lights up on the display panel.)
NOTES:
●
Once the Insert Editing starts, you can not use the other deck.
●
Insert Editing cannot be performed on a VHS/S-VHS cassette
that has had its record safety tab removed, or on a Mini DV
cassette that has had its erase protection switch set to "SAVE".
●
In insert editing, the recording speed (SP/EP) is determined by
the previous recording to be replaced. If the previous
recording's speed changes within a single edit, the inserted
picture will be distorted at the switching point. (VHS deck
only)
●
A small portion of the recording which precedes an insert edit
may become erased.
●
Insert Editing is also possible using the rear connectors.
When using these connectors, be sure to select the correct
REAR AUX INPUT. To select the correct REAR AUX INPUT
("VIDEO" or "S-VIDEO"), follow steps
5
,
8
, and
9
from the
"Edit From A Camcorder" section,
Z
pg 55.
●
Insert Editing is not possible using the DV IN/OUT connector.
C.RESET
PLAY
PLAY
INSERT
PAUSE
JOG/SHUTTLE
SHUTTLE
JOG
STOP
STOP
PAUSE
A. DUB